Siemens 7MB2041 Скачать руководство пользователя страница 60

Страница: 60 / 152

Operation

5.4 Operating functions

OXYMAT 64

Operating Instructions, 06/2008, A5E00880383-03

5.4.3.6

Autocal (function 24)

Note
You can only make use of automatic calibration (Autocal) if your device contains additional

electronics (optional board). If this isn't the case, a corresponding message will appear on

the display when the Autocal function is called.
Automatic calibration can only be started if the device is in the "Measure" operating state!

Autocal/-check O

Figure 5-14 Autocal function

Note
The settings for "Autocal/Check..." (subfunctions 1 to 3) are valid both for Autocal (automatic

calibration) and for Autocal Check (automatic check that the set calibration tolerances are

complied with, without calibration).
The settings for "Autocal Check" (4th subfunction) only refer to the check of the calibration

tolerances without calibration.

AUTOCAL/Check operating mode

Autocal/-check mode O

Figure 5-15 AUTOCAL/Check operating mode

Содержание 7MB2041

























































































































































Результаты поиска

Содержание 7MB2041

Отзывы:

Siemens 7MB2041, Руководство по эксплуатации, Страница: 60 / 152

Результаты поиска

Содержание 7MB2041

Отзывы: