Siemens 7MB2041 Скачать руководство пользователя страница 110

Страница: 110 / 152

Repair, maintenance and servicing

6.5 Cleaning the device

OXYMAT 64

108

Operating Instructions, 06/2008, A5E00880383-03

Replacement of mains fuses

Even if only one mains fuse is defective, always replace both mains fuses! To replace,

proceed as follows:
1.

Disconnect the device from the mains.

Open the fuse insert at the mains connection socket of the device and remove this.

Check the fuses for damage.

In case of damage, replace both fuses by fuses which have the required rating.

Insert the fuse insert again.

6.5

Cleaning the device

Cleaning the surface

CAUTION

Make absolutely sure that no water penetrates the device during cleaning.

The front panels and doors are washable. Use a sponge or cloth dampened by water

containing washing-up liquid. In particular, the surface in the display area must only be

cleaned with a gentle pressure to prevent damage to the thin foil. Make sure that no water

penetrates the device during cleaning.

NOTICE

In the case of devices used in hazardous areas, the control panel (keyboard and window)

must only be cleaned with a damp cloth.

Cleaning the interior

After opening the device, you can blow out the interior carefully with a compressed air gun, if

necessary.

Содержание 7MB2041

























































































































































Результаты поиска

Содержание 7MB2041

Отзывы:

Siemens 7MB2041, Руководство по эксплуатации, Страница: 110 / 152

Результаты поиска

Содержание 7MB2041

Отзывы: