Siemens 3VA1 100 A Скачать руководство пользователя

Страница: 416 / 532

Accessories

4.14 DIN rail adapter

3VA molded case circuit breakers

416

Manual, 04/2015, A5E03603177010-02

4.14.2

Information about installation, assembly and attachment

3VA1 160 1-pole and 2-pole molded case circuit breakers

3VA1 160 1-pole molded case circuit breakers
To attach these to a DIN rail, a 3VA9181-0SH10 DIN rail adapter is required. This DIN rail

adapter is not attached by screws to the molded case circuit breaker, but simply snapped

into place on the rear panel.

3VA1 160 2-pole molded case circuit breakers
To attach 2-pole molded case circuit breakers to 35 mm DIN rails, a 3VA9182-0SH10 DIN

rail adapter is required. This adapter is fitted with threaded nuts. The molded case circuit

breakers are screwed onto the adapter by means of the fastening screws supplied with the

circuit breakers. The nuts supplied with the circuit breakers are not required.

3VA1 100 and 3VA1 160 3-pole and 4-pole molded case circuit breakers

To attach 3-pole and 4-pole molded case circuit breakers to 35 mm DIN rails, a 3VA9187-

0SH10 DIN rail adapter is required. This adapter is fitted with threaded nuts. The molded

case circuit breakers are screwed onto the adapter by means of the fastening screws

supplied with the circuit breakers. The nuts supplied with the circuit breakers are not

required.

3VA1 100 and 3VA1 160 3-pole and 4-pole molded case circuit breakers with side mounted residual

current device

The 3VA9187-0SH20 DIN rail adapter has been specially developed for use with molded

case circuit breakers combined with side mounted residual current device. This DIN rail

adapter is also fitted with threaded nuts so that the molded case circuit breaker/residual

current device assembly can be fastened to it by means of the screws included in the scope

of supply of both devices.

Assembly instructions
The molded case circuit breaker must first be attached to the DIN rail adapter. 3-pole molded

case circuit breakers must be attached such that their right-hand edge (when viewed from

above) is flush with the DIN rail adapter. With 4-pole molded case circuit breakers, the N

pole is situated opposite on the left-hand side (when viewed from above). The screws are

inserted in the fastening holes between phases 1 and 2, and between phases 2 and 3, in the

molded case circuit breaker.
After the molded case circuit breaker has been attached to the DIN rail adapter, the residual

current device must also be mounted on the adapter. After the residual current device has

been secured in position on the DIN rail adapter, the main current paths of the residual

current device and the molded case circuit breaker must be checked to ensure that they are

properly aligned and connected.

Содержание 3VA1 100 A





















































































































































































































































































































































































































































































































































Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Похожие инструкции для 3VA1 100 A

Бренды по названию

Популярные бренды

Siemens 3VA1 100 A, Руководство пользователя

Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Похожие инструкции для 3VA1 100 A

Бренды по названию

Популярные бренды