Siemens 3VA1 100 A Скачать руководство пользователя

Страница: 337 / 532

Accessories

4.8 Residual current devices

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

337

Operator controls

Insulation tests
It is absolutely essential to isolate the evaluation electronics circuit while insulation tests are

in progress in order to protect the circuit against potential damage on the one hand and to

prevent detection of insulation faults due to the power pack on the other. This is done simply

by withdrawing (15 - 17 mm) the circuit breaker which is anchored in the enclosure.

Disconnection of the main conductor connections is thus unnecessary. On completion of the

tests, the circuit breaker must be pushed back into position before the residual current

device is commissioned.

Testing and resetting the residual current device

Testing
Depending on operating conditions, the test button on the front panel of the residual current

device should be pressed in order to function-test the device. The test button is labeled with

the letter "T". If the test button is pressed, the device is tested immediately irrespective of the

current delay time setting.
If the test button is pressed, a residual current is simulated on a test winding attached to the

summation current transformer. If the residual current device is functioning properly, it must

trip the molded case circuit breaker.
The test button must be held down for at least 2 seconds. The design of the test button

prevents unintentional actuation.

Note
The residual current device can be successfully tested only if it is connected to a rated

operational voltage which equals at least 85% of the minimum rated operational voltage.

Содержание 3VA1 100 A





















































































































































































































































































































































































































































































































































Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Похожие инструкции для 3VA1 100 A

Бренды по названию

Популярные бренды

Siemens 3VA1 100 A, Руководство пользователя

Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Похожие инструкции для 3VA1 100 A

Бренды по названию

Популярные бренды