Siemens 3VA1 100 A Скачать руководство пользователя страница 151

Страница: 151 / 532

Accessories

4.2 Internal accessories

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

151

The diagram below uses the example of an ET200S to illustrate the conventional method of

connecting the electronics-compatible auxiliary switch AUX, the trip alarm switch TAS and

the motor operator MO320 to a distributed I/O unit.

Further information about contact reliability can be found at the end of this chapter.

Auxiliary switches AUX

The purpose of auxiliary switches is to signal the position of the main contacts of the molded

case circuit breaker. The contacts of the auxiliary switch open and close simultaneously with

the main contacts of the molded case circuit breaker.

Leading changeover switches LCS

Leading changeover switches signal the opening of the main contacts with a lead time of 20

ms in advance of circuit breaker trips and are thus used for load shedding, for example.

Trip alarm switches TAS

Trip alarm switches signal every circuit breaker trip, regardless of the cause of the trip. The

trip alarm switches are operated whenever the molded case circuit breaker switches to the

TRIP position.

Содержание 3VA1 100 A





















































































































































































































































































































































































































































































































































Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Бренды по названию

Популярные бренды

Siemens 3VA1 100 A, Руководство пользователя

Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Бренды по названию

Популярные бренды