SICK GM32 EX Скачать руководство пользователя страница 95

Страница: 95 / 112

10.10

Inadequate purge air supply

CAUTION
A faulty purge air supply can damage the measuring system

The measuring system can no longer be protected from contaminated sample gas and
is damaged.

If there are signs of a faulty purge air supply, immediately perform the measures
listed below.

Indications of inadequate purge air supply

•

Unusual noise from the area of the purge air unit.

•

On systems with pressure difference sensor: An appropriate error message occurs.

•

Rise in enclosure temperature.

•

Unusually rapid contamination of the window of the measuring device.

Check the purge air unit

Remove the purge air hose on the SR-unit: A strong air flow must be noticeable.

Reinstall the purge air hose immediately.

Measures if purge air supply is inadequate

•

If the purge air unit is not immediately functional:

Remove the SR-unit from the gas duct.

•

For a short malfunction:

Swiveling out the SR-unit is sufficient.

•

Immediately restore correct operation of the purge air unit.

•

Replace provisionally by a different purge air supply with at least the same purge
air throughput.

Information for fast correction of faults

•

Air filter of purge air unit clogged?

•

Purge air hose slipped off or broken?

•

Power supply of purge air unit failed?

10.11

Malfunctions on the connection unit

A green LED lights on each power supply unit in the connection unit. If no LED lights:

Check the power supply of the connection unit.
If the power supply to the connection unit exists, contact SICK Customer Service.

TROUBLESHOOTING

8015558/YYJ8/V1.7/2016-07 | SICK

O P E R A T I N G I N S T R U C T I O N S | GM32-Ex

Subject to change without notice

Содержание GM32 EX

















































































































Результаты поиска

Содержание GM32 EX

Отзывы:

Похожие инструкции для GM32 EX

Бренды по названию

Популярные бренды

SICK GM32 EX, Руководство по эксплуатации

Результаты поиска

Содержание GM32 EX

Отзывы:

Похожие инструкции для GM32 EX

Бренды по названию

Популярные бренды