SICK GM32 EX Скачать руководство пользователя страница 54

Страница: 54 / 112

7.5

Aligning the measuring probe in flow direction

Flow direction aligned at the factory

NOTE

The fitting angle of the probe is already set before delivery when the gas flow direction
has been defined during project planning.
A sticker marks the setting.

Figure 23: Flow direction marking

Device flange

Flow direction sticker

Mounting ring screws (4 pcs.)

Measuring probe, aligning

Rotate the device flange to align the probe.

Loosen the 4 screws on the mounting ring (see Figure).

Rotate the device flange to the following position:
–

The measuring gap must point in flow direction.

–

The device flange must be positioned so that the SR-unit can be fitted in a
vertical position.

Tighten the screws on the mounting ring again to fasten the device flange in this
position.

7.6

Connecting protective gas to the SR-unit

The protective gas connection is on the intermediate enclosure.

COMMISSIONING

O P E R A T I N G I N S T R U C T I O N S | GM32-Ex

8015558/YYJ8/V1.7/2016-07 | SICK

Subject to change without notice

Содержание GM32 EX

















































































































Результаты поиска

Содержание GM32 EX

Отзывы:

Похожие инструкции для GM32 EX

Бренды по названию

Популярные бренды

SICK GM32 EX, Руководство по эксплуатации

Результаты поиска

Содержание GM32 EX

Отзывы:

Похожие инструкции для GM32 EX

Бренды по названию

Популярные бренды