Sharp MX-M1054 Скачать руководство пользователя страница 9

Страница: 9 / 76

Consumables

SHARP

Document Solution Centre

FUSING UNIT:

MX-M904 – MX-M1204

Product Code

Description / Contents

Approx. Life

MX-950HK

Fusing Roller Kit:-

•

Upper heat roller unit

•

Lower heat roller unit

1000k

MX-950KC

Fuser Maintenance Kit:-

•

Fusing separation pawl (upper) x6

•

Fusing separation pawl (lower) x4

•

Fusing front paper guide (upper)

500k

MX-950WC

Web Cleaning Kit:-

•

Web roller.

•

Web roller bearing x2

•

Web backup roller

•

Web backup roller bearing x2

•

Web guide shaft

•

Web guide shaft bearing x2

500k

PERIPHERALS

MX-SCX1

Saddle Staple Cartridge (for MXFN22)

5000 staples (x 3)

MX-SCX2

Staple Cartridge (for MXFN21/MXFN22)

5000 staples (x 3)

MX-SCX3

Saddle Staple Cartridge (For MXFN25)

2000 staples (x 4)

MX-SC50

Staple Cartridge (for MX-BM50 – Plockmatic)

5000 staples (x 3)

AR-SC2

Staple Cartridge (for MX-FN24/25)

5000 staples (x 3)

AR-SV1

Stamp Cartridge (for AR-SU1)

2 cartridges

SERVICE ROTATION:

MX-900TU

Transfer Belt Unit

For Service Rotation

MX-900FU

Fusing Unit (230v) for MX-M904 only

MX-901FU

Fusing Unit (230v) for MX-M1054/1204 only

MX-900WU

Web Cleaning Unit

Note:
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.

Содержание MX-M1054













































































Результаты поиска

Содержание MX-M1054

Отзывы:

Sharp MX-M1054, Техническое справочное руководство, Страница: 9 / 76

Результаты поиска

Содержание MX-M1054

Отзывы: