Sharp MX-M1054 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 76

Sharp MX-M1054 Скачать руководство пользователя страница 53

Trouble Codes

SHARP

Document Solution Centre

53

F3

32 Lift up trouble Cassette 3 (Main unit)
42 Lift up trouble Cassette 4 (Main unit)

F6

00  ICU-Fax communication trouble (ICU)
01  Fax EEPROM read/write error.
04  Fax modem operation trouble.
21  LIU & Fax soft switch error (combination)
30  Access error to 1-chip on Fax board.
97  Fax Pwb compatibility trouble.
98  Improper Fax & Destination information.

F9

91 Communication error between MFP and

printer section when booting.

92 Printer PWB hardware error

FF

00 Double feed detection trouble (PCU)
10 Double feed detection trouble (SCU)

H2

00 Thermistor open trouble (TH_UM_AD2)
02 Contact thermistor upper sub detection

thermistor open

03 Non-contact thermistor upper main

compensation thermistor open

H3

00 Fuser high temperature (TH_UM).
02 Fuser high temperature (TH_US).

H4

00  Fuser low temperature (TH_UM_AD2)
02  Fuser low temperature (TH_US)
30  Upper main thermistor differential input

abnormality (TH_UM)

H5

01 5 continuous (POD1 not reach) jams

H7

10 Fuser low temperature recovery error

(TH_UM_AD2)

H7

12 Fuser low temperature recovery error

(TH_US)

L1

00 Scanner feed trouble.

L2

11 Lamp cooling fan motor trouble

L3

00 Scanner return trouble.

L4

01  Main motor lock trouble
02  Main motor 2 lock trouble
03  Fusing motor trouble
04  Toner hopper motor/Developing motor lock

trouble

14  Toner cartridge motor lock trouble
17  Drum motor lock trouble (K)
27  Decurler motor lock trouble
28  Sub power source cooling fan motor
30  Controller fan motor
31  Machine heat exhaust fan trouble
32  Power source cooling fan trouble
34  LSU/Polygon cooling fan trouble
36  Toner suction fan trouble
38  Reverse transport cooling fan trouble
39  Reverse cooling fan motor trouble
40  Ozone fan motor 1 trouble
41  Ozone fan motor 2 trouble
43  Paper cooling fan trouble
46  Development cooling fan trouble
47  Power cooling fan 3 trouble
48  ADU transport cooling fan 1 motor trouble
49  ADU transport cooling fan 2 motor trouble
50  Process suction fan trouble
54  PS cooling fan trouble
58  Process section peripheral fan trouble

L6

10 Polygon motor trouble (LSU)

«
...
51
52
53
54
55
...
»

Содержание MX-M1054













































































Отзывы:

Нет отзывов