Sharp MX-M1054 Скачать руководство пользователя страница 71

Страница: 71 / 76

Repair Hints

SHARP

Document Solution Centre

SHARP OSA

ALL

Unable to enter the URLs for EAM

(External Accounting Mode) as the item

is missing from the webpage, even

though MXAMX3 is enabled.

Check the setting for Sim 26-03 (Coin Vendor Mode).

Ensure OUTSIDE AUDITOR is configured to None.

Is it possible to activate a trial mode for

Sharp OSA?

Sharp OSA trial mode supporting most functions can be

enabled by executing Sim 26-74 (restricted to approx
32000 pages, including print/scan/copy/image send).

EMAIL STATUS ALERTS

All

Is it possible to configure the MFP to

send only a single email alert for each

alert condition?

To enable single email alert notification for Customer

Email address only, configure the following soft switch:-

SIM 55-03 SW28-3 (change from 0 to 1).

Note: For dealer email address, multiple email

notifications will still be received.

PRINT CONTROLLER

ALL

When printing multiple page reports

from different paper trays as separate

files, is it possible to stop the MFP

device from bypassing jobs held when a

paper out condition occurs, to prevent

an out of sequence output/report?

Enable (check) the following setting change on the MFP

device:-

System Settings - Operation Settings - Disabling of Bypass

Printing

DATA SECURITY KIT

MX-FR38U

When printing to a specific folder

without PIN, Error 421 occurs - only

when DSK is installed.

To print to a specific folder without PIN, perform the

following setting changes:-

Settings - Security Settings - Other Settings -
Disabling of Document Filing menu:-

Un tick Sharing Mode for Printer.

User Control - Authority Group List - Add
Authority group Registration - Job Setting -
Security - Document Filing Approval Setting
menu:- Enable Sharing Mode.

Содержание MX-M1054













































































Результаты поиска

Содержание MX-M1054

Отзывы:

Sharp MX-M1054, Техническое справочное руководство, Страница: 71 / 76

Результаты поиска

Содержание MX-M1054

Отзывы: