Sharp MX-M1054, Техническое справочное руководство, Страница: 49 / 76

Test Simulation
SHARP
Document Solution Centre
49
60
Memory Operation & Test
1 SDRAM read/write test (MFP PWB)
61
LSU Writing Adjustment/Test
1 LSU test (Polygon & BD detection check)
3 LSU power auto setup
4 LSU position adjustment.
11 LSU power correction (automatic)
12 LSU power manual correction
13 LSU power correction value reset/clear
62 HDD Operation & Test
1 HDD/SD Card format
2 HDD partial read/write check
3 HDD read/write check (all areas)
6 Smart (HDD) self diagnostic test
7 Smart (HDD) self diagnostic error log
8 HDD/SD Card format (excluding system &
operation manual area)
10 Job completion list deletion (with job log)
11 Document filing data deletion
12 Enable/disable auto format for HDD
trouble.
13 HDD format (manual area only)
14 Delete document filing management data
20 Check operation of mirroring hard disk
63
CCD Operation & Adjustment
1 Shading correction data display
2 Shading correction execution (force)
3 CCD gamma & colour correction adjust.
4 SIT chart patch density list display
5 CCD gamma & colour correction reset.
6 Print engine colour balance
7 Standard target colour calibration set-up
8 Standard scanner target reset (Service)
64
Self Test Print
2 Test print (B/W mode)
4 Printer self print test
5 Printer self print test (PCL)
6 Printer self pint test (PS)
7 Adjustment pattern print (Sim46-21)
65
LCD Operation & Adjustment
1 LCD touch panel adjustment
2 LCD touch panel adjustment result display
5 Operation panel key input test
66
Fax Control Settings & Adjustments
1 Fax Soft SW setting
2 Country code default set (Fax)
3 Fax PWB controller memory check
4 Fax signal line check (Max level)
5 Fax signal line check (Soft SW setting level)
6 Fax list print (confidential registration)
7 Fax memory printout (all data)
8 Fax sound message setup
9 Fax signal line check (Soft SW setting)
10 Fax all memory clear
11 Voice signal check (line/speaker 300bps)
12 Voice signal check (line/speaker 300bps)
13 Register dial number for Sim 66-14/15/16
14 Adjust/check the time dial pulse (10bps)
15 Adjust/check the time dial pulse (20bps)
16 Adjust/check the send level DTFM signal
17 DTFM signal to send to line (Max level)
18 DTFM signal to send to line (Soft Sw level)
21 Print various registration information
22 Set the sound volume of the handset
24 Fast memory data clear
25 Register Fax number for modem dial in
26 Register external tel. number for Modem
dial in
29 Fax address book clear
30 Tel/LIU sensor status check
31 ON/OFF setting of output port (Tel/LIU)
32 Received data check (comparison)
33 Busy Tone/CNG/CED/FNET detect check
34 Display time required for sending test data
36 Check Send/Receive from modem.
39 Check Destination saved in Fax EEPROM
42 Rewrite PIC program installed on Fax box
43 Write program & adjustment values of PIC
60 Register ACR data
67
Printer Settings & Adjustments
17 Printer NVRAM clear
24 Printer half tone auto adjustment
25 Printer half tone manual adjustment
27 Setup target of printer calibration (Service)
28 Std target of printer calibration (Service)
31 Printer calibration data clear
32 Printer screen gamma setting (300/600dpi)
33 Printer screen gamma adjust. (PCL/PS)
34 Engine maximum adjustment mode for
printer