Sharp MX-M1054 Скачать руководство пользователя страница 13

Страница: 13 / 76

Density & Gradation Adjustment

SHARP

Document Solution Centre

Automatic Grey Balance Calibration - FACTORY MODE

Note: When adjusting grey balance adjustment before or after routine maintenance, always use the

recommended paper (Mondi 90gsm or equivalent) for optimum image quality.

HIGH DENSITY PROCESS CONTROL:

[Execute]

Sim 44-06

HALFTONE PROCESS CONTROL:

[Execute]

Sim 44-26

GREY BALANCE ADJUSTMENT:

Sim 46-74

[Engine & Printer]

FACTORY MODE

Place printed test pattern onto glass for both Copy &

Printer modes.

Manual Colour Calibration – SERVICE MODE

HIGH DENSITY PROCESS CONTROL:

[Execute]

Sim 44-06

HALFTONE PROCESS CONTROL:

[Execute]

Sim 44-26

GREY BALANCE ADJUSTMENT:

Sim 46-74

[Engine & Printer]

SERVICE MODE

Place printed test pattern onto glass for both Copy &

Printer modes.

GREY BALANCE MANUAL ADJUSTMENT:

Sim 46-21

[for Engine]

Sim 67-25

[for Printer]

Adjust K (17 points) for Copy & Printer Modes.

Содержание MX-M1054













































































Результаты поиска

Содержание MX-M1054

Отзывы:

Sharp MX-M1054, Техническое справочное руководство, Страница: 13 / 76

Результаты поиска

Содержание MX-M1054

Отзывы: