Shanghai Siheng Motor KA Series Скачать руководство пользователя страница 36

Страница: 36 / 39

- 36/27 -

Shanghai Siheng Motor Co Ltd

www.sihengmotor.com

Alarm

Code

Alarm name

Running status

Reasons

Handling method

Position error

Switch on the main
power supply and
control

line,

input

instruction

pulse,

motor does not rotate

①

Wrong connection of U, V and W leads of

motors

②

Wrong lead of encoder cable.

Correct connection

Encoder failed

Replace the servo motor.

The detection range of setting position

deviation is too small.

Increase the detection range of out-of-

tolerance position.

Position proportional gain is too small.

Increase gain.

Insufficient torque.

①

Check the torque limit.

②

Reduce the load capacity.

③

Replace high power servo drivers

and motors

。

Command pulse frequency too high.



reduce frequency

Motor

overheating

Appears when
switching on the
control power

Circuit board failure.

Replace the servo motor driver.

①

cable is broken.

②

Motor internal temperature relay damaged

①

Check the cables.

②

Check the Motor.

Motor appears during
operation

Motor overload.

①

Reduce the load.

②

Reduce start and stop frequency.

③

Reduce the torque limit.

④

Reduce the relevant gain.

⑤

Replace high power ac servo drive

unit and motor

Motor internal fault.

Replace the servo motor.

Speed amplifier
saturation
failure

Motor appears during
operation

motor jammed mechanically.

Check the mechanical part of the load.

Over load

①

Reduce the load

②

Replace high power servo drivers

and motors.

Driver disable

exception

CCW, CW drive forbidden input terminal

Disconnect.

。

Check wiring and power supply for input

terminals.

Position
deviation
counter
overflow

①

motor jammed mechanically.

②

Abnormal input instruction pulse

①

Check the mechanical part of the

load.

②

Check the command pulse.

③

Check whether the motor receives

the instruction pulse to rotate.

Encoder Failed

Encoder wiring error.

Check wiring

encoder is damaged.

Replace the servo motor.

Bad encoder cable

Change cable

The encoder cable is too long, resulting in low

power supply voltage of the encoder.

①

Shorten the cable.

。

②

Multi-core parallel power supply is

adopted

。

Control under
voltage of
power supply

Input control internal 15V voltage is low

Check the control power

。

①

Bad internal connector of servo driver.

③

Abnormal switching power supply.

③

Chip is damaged.

①

Replace the servo motor driver.

②

Check the connectors.

③

Check the switching power supply.

Содержание KA Series








































Результаты поиска

Содержание KA Series

Отзывы:

Бренды по названию

Популярные бренды

Shanghai Siheng Motor KA Series, Руководство пользователя

Результаты поиска

Содержание KA Series

Отзывы:

Бренды по названию

Популярные бренды