Shanghai Siheng Motor KA Series Скачать руководство пользователя

Страница: 2 / 39

- 2/27 -

Shanghai Siheng Motor Co Ltd

www.sihengmotor.com

Note



Before starting operation, please make sure that you can start the emergency

switch and shut down at any time.



When commissioning, please separate the servo motor from the machine. After the

action is confirmed, the motor is installed on the machine.



After the servo motor stops and restores instantaneously, do not approach the

machine. The machine may suddenly start again.



Do not switch on or off the power frequently, otherwise it will cause overheating

inside the driver.

peration

Function

Stop



When the motor is running, do not contact any rotating parts, otherwise it will cause

casualties.



When the equipment is running, it is forbidden to touch the driver and motor,

otherwise it will cause electric shock or scald.



When the equipment is running, it is forbidden to move the connecting cable,

otherwise it will cause personal injury or equipment damage.

Содержание KA Series








































Результаты поиска

Содержание KA Series

Отзывы:

Похожие инструкции для KA Series

Бренды по названию

Популярные бренды

Shanghai Siheng Motor KA Series, Руководство пользователя

Результаты поиска

Содержание KA Series

Отзывы:

Похожие инструкции для KA Series

Бренды по названию

Популярные бренды