Shanghai Siheng Motor KA Series Скачать руководство пользователя

Страница: 27 / 39

- 27/27 -

Shanghai Siheng Motor Co Ltd

www.sihengmotor.com

Parameters No

Name

Function

parameter

scope

P01.01

JOG

Running speed

①

Set the running speed of JOG operation.

-3000

～

3000

r/min

P01.02

Acceleration and
deceleration time
constant

①

The setting value is the acceleration time of the motor from 0 to 1000 r/min

②

The acceleration and deceleration characteristics are linear

③

For speed control only, position control is invalid

④

This parameter should be set to 0 if the servo driver is used in combination with an

external position ring

～

10000ms

P01.03

Maximum speed
limit

①

Set the maximum speed limit of the servo motor

②

It has nothing to do with the direction of rotation.

③

If the setting value exceeds the rated speed, the actual maximum speed limit is the

rated speed

～

6000

r/min

P01.04

Internal speed

①

Set internal speed 1.

②

In the speed control mode, when SC1 is OFF and SC2 is OFF, the internal speed 1

is selected as the speed instruction.

-3000

～

3000

r/min

P01.05

Internal speed

①

Set internal speed 2

②

In the speed control mode, when SC1 is ON and SC2 is OFF, the internal speed 2

is selected as the speed instruction.

-3000

～

3000

r/min

P01.06

Internal speed

①

Set internal speed 3.

②

In the speed control mode, when SC1 is OFF and SC2 is ON, select internal speed

3 as the speed instruction.

-3000

～

3000

r/min

P01.07

Internal speed

①

Set internal speed 4.

②

In the speed control mode, when SC1 is ON and SC2 is ON, select internal speed

4 as the speed instruction.

-3000

～

3000

r/min

P01.08

Reach the speed

①

Set arrival speed

②

In the non-position control mode, if the motor speed exceeds the set value, SCMP

ON, otherwise SCMP OFF.

③

In position control mode, this parameter is not used

④

It has nothing to do with the direction of rotation

⑤

The comparator has hysteresis characteristics

～

3000

r/min

P01.10

Internal CCW

The torque limit

①

Set internal torque limit value of servo motor CCW direction.

②

The setting value is the percentage of the rated torque, for example 2 of the rated

torque X, set the value to 200.

③

This restriction is valid at all times.

④

If the set value exceeds the maximum allowable overload capacity of the system,

the actual torque is limited to the maximum allowable overload capacity of the
system.

～

300%

P01.11

Internal CW torque
limits

①

Set internal torque limit value of CW direction servo motor.

②

The setting value is the percentage of the rated torque, for example 2 of the rated

torque

X, the value is set to -200

③

This restriction is valid at all times.

④

If the set value exceeds the maximum allowable overload capacity of the system,

the actual torque is limited to the maximum allowable overload capacity of the
system.

-300%

～

Содержание KA Series








































Результаты поиска

Содержание KA Series

Отзывы:

Похожие инструкции для KA Series

Бренды по названию

Популярные бренды

Shanghai Siheng Motor KA Series, Руководство пользователя

Результаты поиска

Содержание KA Series

Отзывы:

Похожие инструкции для KA Series

Бренды по названию

Популярные бренды