SEW-Eurodrive MFC1/FHX Series Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 164

SEW-Eurodrive MFC1/FHX Series Скачать руководство пользователя страница 120

8

Service

Device replacement

Operating Instructions – MOVI-C

®

FIELD CONTROLLER standard/advanced

120

8.5.3

Replacing the SD memory card

1. Observe the safety notes.
2. Loosen the screws and take off the electronics cover from the connection box.
3. Remove the SD memory card from the electronics cover.
4. Compare the type designation of the SD memory card.

INFORMATION

The new SD memory card must have the same type designation as the previous SD

memory card.

5. Insert the new SD memory card into the electronics cover.
6. Check the startup of the device.

ð

If required, perform startup again or load the saved startup to the device.

INFORMATION

The variable values stored permanently on the MOVI-C

®

FIELD CONTROLLER are

not stored on the SD memory card by default.

ü

Select one of the following procedures to store the variable values on the SD

memory card:

• Program the application (IEC program) accordingly.
• Load the data backup into the engineering software MOVISUITE

®

via the project

management (in preparation).

7. Place the electronics cover onto the connection box and screw it on.
8. Supply the device with voltage.
9. Check the new electronics cover for proper functioning.

26872137/EN – 12/2021

«
...
118
119
120
121
122
...
»

Содержание MFC1/FHX Series





































































































































































Отзывы:

Нет отзывов