SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

UltraWave Product Guide

Page 15

2

Installation

There are two covers on the UltraWave enclosure: the antenna cover and the circuit card cover.
The antenna cover is secured with four inset screws that are factory installed to a finger-tight
torque specification. There are no user-serviceable components in the antenna compartment and
the cover should not be removed for any reason. The circuit card cover is secured with four thumb
screws that are removed to access the circuit card assembly for setup and calibration purposes.

The UltraWave transmitter and receiver units are almost identical, with only minor differences in
component layout.

shows an UltraWave receiver and illustrates the unit’s features. The

receiver’s diagnostic activity LEDs are listed in

.

Note

DO NOT remove or tighten the four screws on the antenna
compartment.
To access the transmitter/receiver circuit card assembly, remove
the four screws on the circuit card cover. When replacing the circuit
card cover, tighten the screws until finger-tight. DO NOT over
tighten the circuit card cover screws.

Figure 10 Opening the UltraWave enclosure

DO NOT remove or tighten the 4 screws
on the antenna compartment cover

remove the 4 screws on the circuit card
compartment’s cover to access the circuit
card for setup and calibration

«
...
13
14
15
16
17
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

Бренд: Data Harvest Страницы: 19

Бренд: Caddx-Caddi Controls Страницы: 6

Multi Gas Clip Simple Plus

Бренд: Gas Clip Technologies Страницы: 20

Бренд: Elko Страницы: 5

Бренд: Bircher Reglomat Страницы: 24

Бренд: Velleman Страницы: 51

Бренд: Elmes Electronic Страницы: 2

CEAG GuideLed Cinema 11011 CG-S

Бренд: Eaton Страницы: 16

DigiLCDDVR Series

Бренд: SecurityMan Страницы: 36

CN-Magnetic-Mini

Бренд: C.Nord Страницы: 2

Бренд: Clover Страницы: 1

VER. 061030 CAM-6500

Бренд: ACTi Страницы: 13

Бренд: Datavideo Страницы: 55

Бренд: Maxouttech Страницы: 3

Бренд: SUREN Страницы: 5

Бренд: Safe Signal Страницы: 4

Бренд: ZMODO Страницы: 6

SG21CD7484UQ-A80

Бренд: Lorex Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды