SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

background image

Page 28

UltraWave Product Guide

Stacking UltraWave units

To increase the height of the microwave field, it is possible to stack two, or three, UltraWave units
on one mounting post. Use the UCM Height Calc tool to determine the required mounting heights
and mounting angles for the stacked units. Each UltraWave sensor must use a different Frequency
Pair. To ensure maximum signal isolation, use Frequency Pairs that are at least two numbers
apart. Do not use Frequency Pairs that are adjacent, consecutive numbers (e.g., use Frequency
Pairs 1, 3, 5, rather than 1, 2, 3). To facilitate the wiring connections, it is recommended that the
receivers be mounted on one post, and the transmitters be mounted on another post.

illustrates the wiring connections for a double stacked UltraWave configuration.

illustrates

a triple stack UltraWave system.

Figure 26: Silver Network Ethernet wiring diagram

maximum 60 receivers/processors

first receiver or

second receiver

last receiver

Network

max. cable run

third receiver

fourth receiver

fifth receiver

Manager
computer

security
management
system
computer

between receiver
or processor and

Category 5 Ethernet cable

class 3

PoE

switch

processor

or processor

or processor

or processor

or processor

or processor

(328 ft.)

PoE switch 100 m

«
...
26
27
28
29
30
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

SET-2000 Oil/Sludge

Бренд: Labkotec Страницы: 14

Бренд: Tamron Страницы: 2

Бренд: Velleman Страницы: 3

Бренд: Watchguard Страницы: 4

Vizzyalarm VZW-02

Бренд: Alderon Industries Страницы: 6

Бренд: Zhejiang Страницы: 33

Бренд: Neostar Electronics Страницы: 2

Бренд: TPG Страницы: 6

Бренд: Umirs Europe Страницы: 24

Бренд: Securiton Страницы: 10

Бренд: Vacron Страницы: 17

Бренд: OpenEye Страницы: 44

Бренд: Satel Страницы: 10

Бренд: Velleman Страницы: 55

NightVision BulletCam

Бренд: Swann Страницы: 2

Бренд: DELTA DORE Страницы: 2

Бренд: Messoa Страницы: 31

Бренд: Ctronics Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды