SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

background image

Setup

Page 32

UltraWave Product Guide

Connect the UCM and specify the Locale

1. Remove the lower cover from the UltraWave transmitter unit enclosure and use a USB cable

to connect the UCM computer to the USB port on the PCB.

2. Start the UCM application and establish a connection.

3. Select the Config tab and specify the Locale (FCC or ETSI).

4. Repeat this procedure for the receiver unit.

Figure 28 Connecting the UCM

Note

It is also possible to connect the UCM to the UltraWave receiver
remotely through the Silver Network Manager (see

).

Figure 29 Connecting the UCM

Note

The first time the UCM connects to the transmitter/receiver units, you
are prompted to select the sensor’s Locale (region of operation - FCC
for North American operation, or ETSI for European operation). Make
the selection based on the country in which the unit is installed. The
UltraWave will not operate until both the transmitter and receiver have
the Locale specified.

select the Network Type

select the Device Type

specify the connection

select Connect to establish

the device ID displays

a UCM connection to the
UtraWave unit

select Work Offline to setup
parameters in a UCM file

select the Network Type

select the Device Type

specify the connection

select Connect to establish

select the IP address of

a UCM connection
select Work Offline to setup
parameters in a UCM file

specify the device Address

the Network Manager PC

select the Network Manager ID

«
...
30
31
32
33
34
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 40

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 41

Бренд: Prime Controls Страницы: 12

Бренд: Abode Страницы: 5

Бренд: Bacharach Страницы: 24

Бренд: D-tect Systems Страницы: 4

Бренд: Abus Страницы: 18

iMEGAPRO IPR7922E

Бренд: Lilin Страницы: 12

VARES ESC-006 A

Бренд: RCS AUDIO-SYSTEMS Страницы: 16

Бренд: Idis Страницы: 51

ClareOne CLR-C1-WTR

Бренд: clare Страницы: 2

Бренд: COHU Страницы: 21

Бренд: jablotron Страницы: 2

Бренд: Orno Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды