SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 52

background image

UltraWave Product Guide

Page 23

requires a normally open, unsupervised momentary switch input. The momentary switch input
must be closed for a minimum of the time specified in the Filter Window parameter (via the UCM).
See

for example input wiring diagrams and supervision resistor values.

In Remote control mode, the two outputs are used by the security management system (SMS) as
output control points. The AUX input is available to report the status of an auxiliary security device
to the SMS.

T6 - transmitter unit outputs

The transmitter unit operates only in Local control mode. T6 connects to output 1 and output 2
(see

for connection details). You can use the UCM to specify the conditions that will

activate the two outputs (see

Alarm data communications on page 11

). The transmitter unit does

not include an input.

Relay contact ratings

The dry contact relays are Form C rated for 30 V @ 1 A maximum, non-inductive load.

Auxiliary input (receiver unit)

In Remote control mode, the receiver’s AUX input provides an auxiliary device input for the
security management system. The receiver determines the input’s status via an internal reference
voltage, and the configuration of the contact closures and supervision resistors. Any change in the
input’s status is reported to the SMS.

Cable ports

Each UltraWave unit includes two 22 mm (0.875 in.) cable ports and two compression glands. Pull
the cables through the compression glands, into the enclosure and through the locking nut. Then
install the compression glands in the cable ports. After making the wiring connections, hand-
tighten the compression glands to provide weather protection and strain relief.

Making the I/O wiring connections

1. Pull the data cable into the enclosure.

2. Prepare the data cable - strip length = 6.4 mm (0.25 in.).

3. Remove the terminal block from T6, make the wiring connections, and then replace the

terminal block (see

).

Enclosure tamper switch

Each UltraWave unit includes a mechanical tamper switch (closed = secure, open = tamper) to
indicate if the enclosure cover is removed. Placing a shunt on header T2 overrides the tamper
switch (shunt ON = secure).

Transmitter/Receiver grounding

1. Connect an approved ground wire to a properly installed ground rod at the UltraWave unit’s

installation location.

2. Connect the ground wire to the ground lug on the transmitter/receiver PCB (see

).

Note

The contact closure input to the AUX input must be voltage-free.

Note

Senstar recommends using a low resistance (5



or less) earth ground

connection at each unit. Consult the local electrical codes for
additional grounding information.

«
...
21
22
23
24
25
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

Бренд: DAKOTA ULTRASONICS Страницы: 163

Бренд: TAC Страницы: 20

Бренд: Eaton Страницы: 12

Бренд: Samsung Wisenet Страницы: 16

Бренд: LaserLine Страницы: 68

Бренд: D+H Страницы: 2

Smart Home Monitoring

Бренд: Rogers Страницы: 20

IPC-HFW1230S1-0280B-S5

Бренд: Dahua Technology Страницы: 17

Бренд: InMotion Страницы: 2

TagShot III-27'

Бренд: Rugged CCTV Страницы: 11

Бренд: V-Tec Страницы: 16

ScoutGuard BG330

Бренд: Boly Страницы: 17

Бренд: Vanderbilt Страницы: 3

Бренд: U-Prox Страницы: 2

ZC-DNT8312NBA-IR

Бренд: Ganz Страницы: 2

Бренд: DSE Страницы: 4

Бренд: Vaxcel Страницы: 7

Бренд: Digitrax Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды