Conquest 100
108
12.5 Sensor Head Backwards Compatibility
The Conquest 100 is fully compatible with earlier versions of the Conquest Sensor Head and
cable so if you have a Conquest Enhanced or Conquest SL Sensor Head available, try
swapping these parts in one at a time and see if you can isolate the problem or solve it.
12.6 Warning Beeps
When acquiring data (either in Line Scan or Grid Scan modes), if the system starts to
“beep”
when it’s not supposed to, there are two possible causes:
1. The operator is holding down the
Enter
button or Display Unit key too long when starting
the Line Scan. The system may register this as two button presses, resulting in the
system starting and stopping immediately. In this instance the triple beep is occurring
because the scan is being stopped. A lighter touch on the button is necessary.
2. The Sensor Head is being pushed too fast. In this case, the DynaQ will also show yellow
and white. To ensure good data quality, simply slow down the speed of the Sensor
Head. In Grid Scan mode, you may be prompted to re-collect that line.
12.7 Sensor Head Keypad Doesn't Respond
If the Sensor Head keypad does not respond, the usual reason is that the Sensor Head has
come unplugged during operation. Power down the system, reconnect the Sensor Head and
restart to restore full keypad functionality.
12.8 Constant Prompt to Perform System Test
If the operator is constantly prompted to run the System Test for the Sensor (
resulting in the inability to collect data, turn off IEP (
5.1.10) in the Preferences menu. If
IEP is disabled, allow the system to warm up for 5 minutes before starting data collection. Also
note that the next time Conquest is powered on, IEP defaults to ON.
If the system is constantly prompting to perform a system test, it may indicate a problem with
the equipment. Scanning can be continued with IEP turned off but if the problem persists, it is
recommended that Sensors & Software Inc. be contacted to help remedy the problem.
12.9 Collecting Test Data
One of the best ways of detecting problems with the Conquest system is by comparing data with
data collected previously.
Soon after receiving the system and getting comfortable with its operation, collect a
24”x24”
(600x600mm) grid of data at a convenient, easily accessible location. The grid should be saved
electronically and perhaps plotted out on paper and dated. The test grid could be collected say,
Содержание CONQUEST 100
