background image

-27-

WARNINGS

This manual contains critical information regarding safe handling, use and care of this system. Harm to 

personnel or property damage could result if all instructions are not followed.

Hazard Description

Hazard Mitigation

Failure to read and understand these 

Instructions for Use is hazardous and 

may result in injury to personnel.

Personnel tasked with use and 

maintenance of the device should 

fully familiarize themselves with the 

contents of these Instructions for 

Use and only attempt use of the 

device once they have a complete 

understanding of these Instructions.  

Users should refrain from operating 

or servicing the equipment in any 

manner other than is set forth in 

these Instructions for Use.

Transporting on surfaces which 

are not flat may result in the 

colposcope tipping and causing 

injury to personnel or damage to 

equipment.   

Transport on only flat surfaces.

Tilting the colposcope will create an 

overbalance condition which could 

cause Injury to personnel or damage 

to equipment.

Do not tilt the colposcope.

Use the colposcope on flat surfaces 

only.

Horizontal and vertical forces create 

instability and may result in an 

overbalance condition which could 

cause injury to personnel or damage 

to equipment.

Do not push on the support pole 

surfaces.

Shock hazard. This device contains 

high voltages.  Maintenance of this 

device poses additional hazards.

Do not operate with the cover 

removed.

Employ only authorized and properly 

trained personnel to perform 

maintenance functions

This device emits intense illumination 

that can be harmful.  Eye damage or 

fire hazards exist if used improperly.

Never look directly at the LED ports 

or reflected from the LED or the fiber 

optic light guides.

Limit exposure of tissue or organs 

other than is required for the relevant 

surgical procedures. 

Do not illuminate patient until ready 

and turn illumination off when the 

procedure has been completed.

Do not direct the illumination beam at 

the patient’s eyes/ shield the patient’s 

eyes if necessary.

Do not operate the illuminator with 

the light guides disconnected.

Содержание COLPOSCOPE 935

































Отзывы: