Sears Craftsman 944.600940 Скачать руководство пользователя | Manualshive

Страница: 26 / 60

background image

26

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•

Raise hood.

•

Pull bulb holder out of the hole in the backside of the grill.

•

Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.

•

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
•

Check wiring. See electrical wiring diagram in the Repair
Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The fuse
holder is located behind the dash.

HEADLIGHT
WIRE
CONNECTOR

FIG. 32

HOOD

TO ADJUST ATTACHMENT LIFT SPRING
(See Fig. 31)

•

While holding spring bushing with wrench, loosen jam
nut.

•

Turn adjustment bolt clockwise to extend spring and
reduce lift effort for heavier attachments.

•

Turn adjustment bolt counterclockwise for lighter at-
tachments.

•

Retighten jam nut against spring bushing.

IMPORTANT: DO NOT ADJUST FOR MAXIMUM SPRING
TENSION WHEN USING LIGHT ATTACHMENTS SUCH
AS A MOWER. ADJUST LIFT LEVER SPRING TO AID IN
LIFTING ATTACHMENT. DO NOT OVERPOWER SPRING.
WHEN REMOVING ATTACHMENT, ALWAYS ADJUST
SPRING TENSION TO ITS LOWEST POSITION.

ADJUSTMENT
BOLT

JAM NUT

ATTACHMENT
LIFT SPRING

SPRING BUSHING

FIG. 31

TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 32)

•

Raise hood.

•

Unsnap headlight wire connector.

•

Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.

•

To replace, reverse above procedures.

IDLE FUEL ADJUSTING
NEEDLE

IDLE SPEED ADJUSTING
SCREW

STOP
SCREW

CLAMP
SCREW

CHOKE CONTROL CABLE

THROTTLE
CONTROL
CABLE

ENGINE

Maintenance, repair or replacement of the emission control
devices and systems, which are being done at th customers
expense, may be performed by any non-road engine repair
establishment or individual. Warranty repairs must be
performed by an authorized manufacuter's service outlet.

TO ADJUST THROTTLE CONTROL CABLE
(See Fig. 33)

The throttle control has been preset at the factory and
adjustment should not be necessary. Check adjustment as
described below before loosening cable. If adjustment is
necessary, proceed as follows:
•

With engine not running, move throttle control lever to
fast position.

•

Check that speed control lever is against stop screw. If
it is not, loosen casing clamp screw and pull throttle
cable until lever is against screw. Tighten clamp screw
securely.

FIG. 33

«
...
24
25
26
27
28
...
»

Содержание Craftsman 944.600940





























































Отзывы:

Нет отзывов

Похожие инструкции для Craftsman 944.600940

Proxima 70 2012

Бренд: Zetor Страницы: 214

Бренд: Zanussi Страницы: 104

Бренд: Curtis Страницы: 8

JOHN DEERE 4120

Бренд: Curtis Страницы: 11

Бренд: LS Страницы: 46

Бренд: WALTERSCHEID Страницы: 16

WEATHERBRAKE 307022173

Бренд: Femco Страницы: 6

Бренд: MASSEY FERGUSON Страницы: 41

Бренд: Gianni Ferrari Страницы: 65

Бренд: MTZ Страницы: 202

Бренд: MTZ Страницы: 244

Бренд: DFM Страницы: 20

TurboSaw EX2600

Бренд: DFM Страницы: 28

Бренд: Ditch Witch Страницы: 207

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды