Sears Craftsman 944.600940 Скачать руководство пользователя | Manualshive

Страница: 23 / 60

background image

23

SERVICE AND ADJUSTMENTS

•

Make sure attachment clutch and ignition switches are
in “OFF” position.

•

Adjust the three nylon locknuts until space between
clutch plate and rotor measures .012" at all three slot
locations cut in side of brake plate.

NOTE: After installing a new electric clutch, run tractor at full
throttle and engage and disengage electric clutch 10 cycles
to wear in clutch plate.

TO ADJUST ATTACHMENT CLUTCH
(See Fig. 23)

The electric clutch should provide years of service. The
clutch has a built-in brake that stops the pulley within 5
seconds. Eventually, the internal brake will wear which may
cause the mower blades to not engage, or, to not stop as
required. Adjustments should be made by your nearest
authorized service center/department.

NYLON LOCKNUT (3)

BRAKE PLATE

SLOT (3)

ROTOR

CLUTCH PLATE

.012"

FIG. 23

TO ADJUST BRAKE (See Fig. 24)

Your tractor is equipped with an adjustable brake system
which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at
high speed in highest gear, then brake must be adjusted.
•

Depress clutch/brake pedal and engage parking brake.

•

Measure distance between brake operating arm and nut
“A” on brake rod.

•

If distance is other than 1-1/2", loosen jam nut and turn
nut “A” until distance becomes 1-1/2". Retighten jam nut
against nut “A”.

•

Road test tractor for proper stopping distance as stated
above. Readjust if necessary. If stopping distance is
still greater than six (6) feet in highest gear, further
maintenance is necessary. Contact your nearest au-
thorized service center/department.

WITH PARKING BRAKE “ENGAGED”

1-1/2"

NUT
“A”

JAM NUT

OPERATING
ARM

FIG. 24

FIG. 22

SECONDARY
IDLER ARM

L.H.
MANDREL

MOWER BLADE
DRIVE BELT

CENTER
MANDREL

IDLER
PULLEY

R.H.
MANDREL
COVER

SPRING

SWAY-BAR
BRACKET

SCREW

TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 22)

Park the tractor on level surface. Engage parking brake.
•

Remove mower drive belt (See “TO REPLACE MOWER
DRIVE BELT” in this section of this manual).

•

Remove mower (See “TO REMOVE MOWER” in this
section of this manual).

•

Remove screws from R.H. mandrel cover and remove
cover. Unhook spring from bolt on mower housing.

•

Carefully roll belt off R.H. mandrel pulley.

•

Remove belt from center mandrel pulley, idler pulley,
and L.H. mandrel pulley.

•

Remove any dirt or grass which may have accumulated
around mandrels and entire upper deck surface.

•

Check secondary idler arm and idler to see that they
rotate freely.

•

Be sure spring is hooked in secondary idler arm and
sway-bar bracket.

•

Install new belt in lower groove of L.H. mandrel pulley,
idler pulley, and center mandrel pulley as shown.

•

Roll belt over R.H. mandrel pulley. Make sure belt is in
all grooves properly.

•

Reconnect spring to bolt in mower housing and reinstall
R.H. mandrel cover.

•

Reinstall mower to tractor (See “INSTALL MOWER AND
DRIVE BELT” in the Assembly section of this manual).

•

Reassemble mower drive belt (See “TO REPLACE
MOWER DRIVE BELT” in this section of this manual).

«
...
21
22
23
24
25
...
»

Содержание Craftsman 944.600940





























































Отзывы:

Нет отзывов

Похожие инструкции для Craftsman 944.600940

Бренд: Troy-Bilt Страницы: 36

PROXIMA PLUS 90 2012

Бренд: Zetor Страницы: 212

Бренд: Mahindra Страницы: 87

Бренд: Husqvarna Страницы: 60

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 112

Бренд: Wallenstein Страницы: 28

COMPAX CL 25 NC

Бренд: Zetor Страницы: 108

10641 Forterra turbo

Бренд: Zetor Страницы: 315

Бренд: Case IH Страницы: 51

OPTIMAL UPX Series

Бренд: Trejon Страницы: 44

Бренд: Poulan Pro Страницы: 56

Бренд: NuTone Страницы: 8

EZ-Pilot Farmall 105C

Бренд: Tribe Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды