Sears Craftsman 944.600940 Скачать руководство пользователя | Manualshive

Страница: 22 / 60

background image

22

SERVICE AND ADJUSTMENTS

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF
THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS
NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS
EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing
should be adjusted so the front is approximately 1/8" to 1/2"
lower than the rear when the mower is in its highest position.
Check adjustment on right side of tractor. Measure dis-
tance “F” directly in front of and behind the mandrel at
bottom edge of mower housing as shown.
•

Before making any necessary adjustments, check that
both front links are equal in length.

•

If links are not equal in length, adjust one link to same
length as other link.

•

To lower front of mower housing, loosen nut “G” on both
front links an equal number of turns.

•

When distance “F” is 1/8" to 1/2" lower at front than rear,
tighten nut “H” against trunnion on both front links.

•

To raise front of mower housing, loosen nut “H” from
trunnion on both front links. Tighten nut “G” on both
front links an equal number of turns.

•

When distance “F” is 1/8" to 1/2" lower at front than rear,
tighten nut “H” against trunnion on both front links.

NOTE: Each full turn of nut “G” will change dim. “F” by
approximately 3/8".
•

Recheck side-to-side adjustment.

TRUNNION

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

FRONT
LINKS

NUT
“ G ”

NUT
“H”

FIG. 20

“F”

“F”

MANDREL

FIG. 19

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 21)
•

Park tractor on a level surface. Engage parking brake.

•

Remove screws from L.H. mandrel cover and remove
cover.

•

Roll belt over the top of L.H. mandrel pulley.

•

Remove belt from electric clutch pulley.

•

Remove belt from idler pulleys.

•

Remove any dirt or grass clippings which may have
accumulated around mandrels and entire upper deck
surface.

•

Check primary idler arm and two idlers to see that they
rotate freely.

•

Be sure spring is securely hooked to primary idler arm
and bolt in mower housing.

MOWER DRIVE BELT INSTALLATION (See Fig. 21)
•

Install belt in both idlers. Make sure belt is in both belt
keepers at the idlers as shown.

•

Install new belt onto electric clutch pulley.

•

Roll belt into upper groove of L.H. mandrel pulley.

•

Carefully check belt routing making sure belt is in the
grooves correctly and inside belt keepers.

•

Reassemble L.H. mandrel cover.

IDLER
PULLEYS

L.H.
MANDREL
COVER

SCREWS

BELT
KEEPERS

L.H.
MANDREL

ELECTRIC
CLUTCH
PULLEY

MOWER
DRIVE BELT

PRIMARY
IDLER ARM

BOLT IN
MOWER
HOUSING

SPRING

«
...
20
21
22
23
24
...
»

Содержание Craftsman 944.600940





























































Отзывы:

Нет отзывов

Похожие инструкции для Craftsman 944.600940

HiTech T Series

Бренд: Valtra Страницы: 31

Бренд: GOLDONI Страницы: 46

Бренд: Yanmar Страницы: 16

Бренд: Quake Global Страницы: 35

Бренд: Valtra Страницы: 414

Бренд: Land Pride Страницы: 50

Бренд: Land Pride Страницы: 32

Бренд: Barko Страницы: 174

Бренд: Challenger Страницы: 51

Бренд: Cub Cadet Страницы: 32

Бренд: Cub Cadet Страницы: 32

Бренд: Daedong Страницы: 12

Бренд: Tecnoma Страницы: 133

Бренд: Nitro motors Страницы: 33

Бренд: MID WEST PRODUCTS Страницы: 4

Бренд: MTW Страницы: 123

Бренд: Ariens Страницы: 36

Бренд: Ariens Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды