Sears Craftsman 944.600940 Скачать руководство пользователя | Manualshive

Страница: 9 / 60

background image

9

FIG. 5

ASSEMBLY

•

Turn height adjustment knob clockwise to remove slack
from mower suspension.

•

Raise deck to highest position.

•

Adjust gauge wheels before operating mower as shown
in the Operation section of this manual.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for
shipping purposes. Correct tire pressure is important for
best cutting performance.
•

Reduce tire pressure to PSI shown in “PRODUCT
SPECIFICATIONS” section of this manual.

CHECK MOWER LEVELNESS

For best cutting results, mower should be properly leveled.
See “TO LEVEL MOWER HOUSING” in the Service and
Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL
BELTS

See the figures that are shown for replacing motion, mower
drive, and mower blade drive belts in the Service and
Adjustments section of this manual. Verify that the belts are
routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that
the brake is properly adjusted. See “TO ADJUST BRAKE”
in the Service and Adjustments section of this manual.

INSTALL MOWER AND DRIVE BELT
(See Figs. 4 and 5)

Be sure tractor is on level surface and mower suspension
arms are raised with attachment lift control. Engage parking
brake.
•

Cut and remove ties securing anti-sway bar and belts.
Swing anti-sway bar to left side of mower deck.

•

Slide mower under tractor with discharge guard to right
side of tractor.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN
ALL MOWER PULLEY GROOVES. INSTALL BELT INTO
ELECTRIC CLUTCH PULLEY GROOVE.

•

Install one front link in top hole of the L.H. front mower
bracket and L.H. front suspension bracket. Retain with
two single loop retainer springs as shown.

•

Install second front link in R.H. front suspension bracket
only and retain with single loop retainer spring as shown.

•

Slide right side of mower back and install link in top hole
of R.H. front mower bracket. Retain with single loop
retainer spring as shown.

•

Turn height adjustment knob counterclockwise until it
stops.

•

Lower mower linkage with attachment lift control.

•

Place the suspension arms on inward pointing deck
pins. If necessary, rock and raise front of mower to align
deck pins with the holes in suspension arms. Retain
with double loop retainer springs with loops down as
shown.

•

Connect anti-sway bar to chassis bracket under left
footrest and retain with double loop retainer spring.

CHASSIS
BRACKET

ANTI-SWAY
BAR

DOUBLE
LOOP
RETAINER
SPRING

GAUGE
WHEEL

IDLER
PULLEY

SUSPENSION
ARMS

FRONT
MOWER
BRACKET

DISCHARGE
GUARD

SINGLE LOOP
RETAINER
SPRINGS

DOUBLE LOOP
RETAINER
SPRING

(Inward

pointing deck pins)

ELECTRIC
CLUTCH
PULLEY

FRONT
SUSPENSION
BRACKETS

FRONT
LINK

USE PLIERS FOR

RETAINER SPRINGS

«
...
7
8
9
10
11
...
»

Содержание Craftsman 944.600940





























































Отзывы:

Нет отзывов

Похожие инструкции для Craftsman 944.600940

Бренд: Taylor-Dunn Страницы: 182

Бренд: Sears Страницы: 24

Бренд: Nogueira Страницы: 84

Бренд: Winton Страницы: 20

Бренд: Yanmar Страницы: 170

Бренд: Bad Boy Страницы: 152

Бренд: Valtra Страницы: 518

Forterra CL 100

Бренд: Zetor Страницы: 198

New Leader NL4330G4

Бренд: FENDT Страницы: 21

Бренд: Century Страницы: 82

Бренд: Husqvarna Страницы: 72

ARGON CLASSIC 55

Бренд: SAME Страницы: 24

Massey Ferguson 1700M Series

Бренд: AGCO Страницы: 51

Бренд: AGCO Allis Страницы: 68

Бренд: Kubota Страницы: 332

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды