Sears Craftsman 944.600940 Скачать руководство пользователя

Страница: 55 / 60

REPAIR PARTS

TRACTOR - - MODEL NUMBER 944.600940

KOHLER ENGINE - MODEL NUMBER CV22S-75518

STARTING SYSTEM

KEY PART
NO. NO.

DESCRIPTION

M-0839070-S

Screw, hex. flange M8x1.25x70

24-096-05-S

Cover, pinion

M-0839080-S

Screw, hex. flange M8x1.25x80

12-468-01-S

Washer, plain 11/32" (3)

25-098-05-S

Starter, (Includes 6-11)

12-221-01-S

Kit, brush

12-227-13-S

Cap

12-211-01-S

Bolt, thru (2)

12-755-54-S

Kit, drive

10.

12-227-06-S

Cap, drive end

11.

12-170-05-S

Armature

ENGINE CONTROLS

KEY PART
NO. NO.

DESCRIPTION

M-642025-S

Screw, hex. flange M6x1.0x25

24-090-14-S

Lever, governor

M-641060-S

Nut, hex. flange M6x1.0

24-089-01-S

Spring, linkage

25-158-08-S

Bushing, linkage retaining

24-079-04-S

Linkage, throttle

25-158-11-S

Bushing, throttle linkage

M-547050-S

Nut, hex. lock M5x0.8

24-089-03-S

Spring, choke return

10.

24-126-56-S

Bracket, control

11.

M-645016-S

Screw, hex. flange M6x1.0x16 (4)

12.

12-237-01-S

Clamp, cable (2)

13.

24-086-43-S

Screw, hex. flange M5x0.8x16 (2)

14.

24-090-07-S

Lever, thorttle actuator

15.

24-468-01-S

Washer, plain 5.5 mm (3)

16.

24-089-15-S

Spring, governor

17.

M-446030-S

Nut, hex M4x0.7

18.

24-090-13-S

Lever, throttle control

19.

M-545020-S

Screw, hex. flange M5x0.8x20

20.

24-089-38-S

Spring, throttle limiter

21.

24-090-05-S

Lever, choke

22.

41-468-03-S

Washer, spring 1/4"

23.

M-403025-S

Screw, hex. cap M4x0.7x25

24.

24-079-05-S

Linkage, choke

NOT ILLUSTRATED

M-545016-S

Screw, hex. flange M5X0.8X16
(Goes into 24-126-56 as a
positive throttle stop)

OIL PAN/LUBRICATION

KEY PART
NO. NO.

DESCRIPTION

M-645025-S

Screw, hex. flange M6x1.0x25 (2)

M-631005-S

Washer, plain 6 mm (2)

24-199-07-S

Pan, oil assembly
(Includes 1,2,&4-10)

24-393-08-S

Oil pump assembly (Includes 5)

24-123-05-S

Tube, oil pickup

24-162-26-S

Screen, oil

24-043-12-S

Kit, governor gear w/pin
(Includes 8)

12-380-01-S

Pin, governor regulating

52-448-02-S

Tab, locking

10.

12-144-02-S

Shaft, governor gear

11.

24-153-08-S

O-Ring

12.

X-75-32-S

Plug, hex. ctsk. 3/8"

13.

24-136-01-S

Nipple, oil filter

14.

52-050-02-S

Filter, oil

15.

52-032-08-S

Seal, oil (PTO end)

16.

24-086-17-S

Screw, hex. flange M8x1.25x45

17.

24-086-16-S

Screw, hex. flange M8x1.25x45 (9)

18.

X-75-10-S

Plug, sq. hd. solid 3/8" N.P.T.F.

NOTE: All component dimensions given in U.S.

inches

1 inch = 25.4 mm

Содержание Craftsman 944.600940





























































Результаты поиска

Содержание Craftsman 944.600940

Отзывы:

Похожие инструкции для Craftsman 944.600940

Бренды по названию

Популярные бренды

Sears Craftsman 944.600940, Руководство пользователя

Результаты поиска

Содержание Craftsman 944.600940

Отзывы:

Похожие инструкции для Craftsman 944.600940

Бренды по названию

Популярные бренды