Sears Craftsman 944.600940 Скачать руководство пользователя | Manualshive

Страница: 6 / 60

background image

6

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

CONNECT BATTERY (See Fig. 2)

CAUTION: Do not short battery termi-
nals by allowing a wrench or any other
object to contact both terminals at the
same time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc.

Positive terminal must be connected
first to prevent sparking from accidental
grounding.

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To
ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the
correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(2) 7/16" wrenches

(1) Tire pressure gauge

(1) 9/16" wrench

(1) Utility knife

(1) 1/2" wrench

(1) 3/4" socket w/drive ratchet

(1) Pliers
When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•

Remove all accessible loose parts and parts cartons
from carton (See page 5).

•

Cut, from top to bottom, along lines on all four corners
of carton, and lay panels flat.

•

Check for any additional loose parts or cartons and
remove.

FIG. 1

BEFORE REMOVING TRACTOR FROM
SKID

ATTACH STEERING WHEEL (See Fig. 1)

•

Remove hex bolt, lock washer and large flat washer
from steering shaft.

•

Position front wheels of the tractor so they are pointing
straight forward.

•

Slide the steering sleeve over the steering shaft.

•

Align tabs and press steering sleeve extension into
bottom of steering wheel.

•

Position steering wheel so cross bars are horizontal
(left to right) and slide onto steering wheel adapter.

•

Secure steering wheel to steering shaft with hex bolt,
lock washer and large flat washer previously removed.
Tighten securely.

•

Snap steering wheel insert into center of steering
wheel.

•

Remove protective materials from tractor hood and
grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES
I N S K I D T H A T M A Y P U N C T U R E T I R E S W H E R E
TRACTOR IS TO ROLL OFF SKID.

STEERING
WHEEL

STEERING SHAFT

STEERING
SLEEVE

STEERING
WHEEL
ADAPTER

LOCK WASHER

STEERING WHEEL
INSERT

HEX BOLT

STEERING
SLEEVE
EXTENSION

TABS

LARGE FLAT
WASHER

«
...
4
5
6
7
8
...
»

Содержание Craftsman 944.600940





























































Отзывы:

Нет отзывов

Похожие инструкции для Craftsman 944.600940

Бренд: jcb Страницы: 31

4400 BROCHURE 74-101

Бренд: MASSEY FERGUSON Страницы: 20

COMPAX CL Series

Бренд: Zetor Страницы: 114

Бренд: Cub Cadet Страницы: 289

Бренд: TMG Страницы: 34

Бренд: matev Страницы: 16

Бренд: matev Страницы: 19

Бренд: matev Страницы: 23

FPS-FKH-Kioti CS 2520

Бренд: matev Страницы: 28

FPS-FKH-Kioti CX 2510

Бренд: matev Страницы: 31

Бренд: matev Страницы: 34

Бренд: matev Страницы: 37

Бренд: Dixon Страницы: 30

Бренд: ArmaTrac Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды