Sears Craftsman 944.600940 Скачать руководство пользователя | Manualshive

Страница: 20 / 60

background image

20

CUSTOMER RESPONSIBILITIES

MUFFLER

Inspect and replace corroded muffler and spark arrester (if
equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” section of this manual.

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil
change if the tractor is used more than 100 hours in one year.

IN-LINE FUEL FILTER (See Fig. 16)

The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
•

With engine cool, remove filter and plug fuel line sec-
tions.

•

Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.

•

Be sure there are no fuel line leaks and clamps are
properly positioned.

•

Immediately wipe up any spilled gasoline.

CLAMP

FUEL FILTER

CLAMP

FIG. 16

CLEANING

•

Clean engine, battery, seat, finish, etc. of all foreign
matter.

•

Keep finished surfaces and wheels free of all gasoline,
oil, etc.

•

Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose to clean your
tractor unless the electrical system, muffler, air filter and
carburetor are covered to keep water out. Water in engine
can result in a shortened engine life.

AIR FILTER (See Fig. 15)

Your engine will not run properly using a dirty air filter. Clean
the foam pre-cleaner after every 25 hours of operation or
every season. Service paper cartridge every 100 hours of
operation or every season, whichever occurs first.

Service air cleaner more often under dusty conditions.
•

Loosen knob and remove cover.

TO SERVICE PRE-CLEANER
•

Slide foam pre-cleaner off cartridge.

•

Wash it in liquid detergent and water.

•

Squeeze it dry in a clean cloth. Allow it to dry.

•

Saturate it in engine oil. Wrap it in clean, absorbent cloth
and squeeze to remove excess oil.

TO SERVICE CARTRIDGE
•

Replace a dirty, bent, or damaged cartridge.

NOTE: Do not wash the paper cartridge or use pressurized
air, as this will damage the cartridge.
•

Remove nut and cartridge plate.

•

Reinstall the pre-cleaner (cleaned and oiled) over the
paper cartridge.

•

Check rubber seal for damage and proper position
around stud. Replace if necessary.

•

Reassemble air cleaner, cartridge plate, and nut.

•

Reinstall air cleaner cover and secure by tightening
knob.

NUT

RUBBER
SEAL

CARTRIDGE

FOAM
PRE-CLEANER

CARTRIDGE
PLATE

KNOB

FIG. 15

«
...
18
19
20
21
22
...
»

Содержание Craftsman 944.600940





























































Отзывы:

Нет отзывов

Похожие инструкции для Craftsman 944.600940

Бренд: DRESSTA Страницы: 177

Бренд: Wheel Horse Страницы: 12

Бренд: Ventrac Страницы: 53

STENSBALLE/NESBO FF/LA

Бренд: GMR Страницы: 36

Elite 15XESSEXF

Бренд: Broan Страницы: 39

Бренд: Valtra Страницы: 41

Бренд: Rev-A-Shelf Страницы: 2

Бренд: Holder Страницы: 190

Бренд: Cub Cadet Страницы: 32

Бренд: Cub Cadet Страницы: 36

Бренд: Bercomac Страницы: 12

Бренд: Bercomac Страницы: 20

Бренд: Bercomac Страницы: 22

Бренд: Bercomac Страницы: 24

Бренд: Bercomac Страницы: 29

Бренд: Bercomac Страницы: 29

Бренд: Bercomac Страницы: 32

Бренд: Bercomac Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды