background image

WARRANTY CONDITIONS 

Warranty Coverage: 

LS Mtron Tractor Division, herein referred to as LS Mtron, undertakes to replace or repair any part of a LS 
loader where damage has been proven to be caused by defects in material or workmanship. 

This Warranty is valid for a period of 1 year from the date of the original retail sale. Parts replaced or 
repaired under the terms of this Warranty are guaranteed only until the original warranty expires. 
Warranty only applies to the original purchaser. 

It is further understood and agreed that the defect should be immediately reported to the Selling Dealer. 
The Selling Dealer will generally perform Warranty repairs or replacements and the Purchaser shall deliver 
the LS Mtron Loader to the Dealer's place of business or repair. 

The obligation of LS Mtron to the Purchaser under this Warranty is limited to the repair or replacement of 
defective parts by an authorized LS Mtron dealer. Repair or replacement in accordance with this Warranty 
shall constitute fulfillment of all liabilities of LS Mtron and the Selling Dealer in respect to LS Mtron 
Loaders. 

There are no warranties beyond those which expressly appear herein. Any implied warranty of 
merchantability or fitness for a particular purpose is specifically excluding here from. 

Warranty Provisions: 

LS Mtron's liability under this warranty is subject to the observance by the Purchaser of the following 
provisions: 

▶  The purchaser shall at all times in the operation of any LS Mtron Product, use those brands and 

grades of lubricating oils, lubricants or fuel and spare parts officially approved by LS Mtron. 

▶  The LS Mtron Loaders shall have been used in accordance with the procedures specified in the 

Operator's Manual. This Warranty does not extend to damage resulting from misapplication, abuse, 
misuse, failure to perform maintenance, negligence, fire, accidents or changes or faulty mounting 
carried out by the Purchaser. When making a Warranty exchange of parts, the Purchaser shall 
compensate LS Mtron for the time that the parts have been used if they have been exposed to 
extreme wear. 

▶  Compensation is not paid for physical harm, deadlock, resulting damages or other losses. 

▶  To obtain warranty service, the Purchaser must (1) report the product defect to an authorized LS 

Mtron dealer and request repair within the applicable warranty term and (2) present evidence of 
purchase. 

▶  The Warranty shall be void if the LS Mtron Loader has been altered or repaired outside of a LS Mtron 

dealership or travel of dealer personnel to customer location for Warranty repair. The customer shall 
also pay any premium for overtime labor requested by the customer. 

▶  Temporary repairs or additional costs due to the work being performed after normal working hours 

will not be compensated. 

▶  The above warranty is in lieu of all other warranties on LS Mtron's behalf and neither party assumes 

any other liability in connection with LS Mtron's Products. 

Right to Make Design and Product Changes: 

LS Mtron reserves the right to make changes in the design and other changes in its LS Mtron Products at 
any time without incurring any obligation with respect to any product previously ordered, sold or shipped. 

Summary of Contents for LL3301















































Reviews: