Sea-doo 2000 Islandia Скачать руководство пользователя | Manualshive

Страница: 80 / 92

background image

78

If repairs are needed to the body or to
the hull contact your dealer. For paint
touch up to mechanical parts use Bom-
bardier spray paint. For minor gelcoat
repairs, a Bombardier repair kit is avail-
able. Replace damaged labels/ decals.

Clean the bilge with hot water and de-
tergent or with bilge cleaner. Rinse
thoroughly. Unscrew drain plug(s) and
lift front end of craft to completely drain
bilge.

Battery

Contact your authorized Sea-Doo dealer.

Anticorrosion Treatment

Wipe off any residual water in the en-
gine compartment.

Lubricate the throttle cable with BOM-
BARDIER LUBE lubricant or equiva-
lent.

Finalizing Storage Preparation

Apply a non abrasive wax to body and
stainless or chromed parts.

The engine cover should be left partial-
ly opened during storage. This will
avoid engine compartment condensa-
tion and possible corrosion.

If the craft is to be stored outside, cov-
er it with a vented opaque tarpaulin to
prevent sun rays and grime from af-
fecting the plastic components, craft
finish as well as preventing dust accu-
mulation.

CAUTION:

Never leave the craft

stored in direct sunlight. UV radia-
tion will dull finishes. The craft must
never be left in water for storage.
Make sure to turn off main battery
selector switch.

For the storage period, it is necessary
to lift the bow up and safely block in
this position so drainage can take
place. Ensure the drain plugs are un-
screwed.

Pre-Season Preparation

Use the Periodic Inspection Chart at
the end of this document and refer to
the pre-season column.

Since technical skills and special tools
are required, some operations should
be performed by an authorized dealer.

NOTE:

It is highly recommended that

an authorized Sea-Doo dealer perform
at the same time the annual safety in-
spection in addition to the pre-season
preparation.

m

WARNING

Observe WARNINGS and CAU-
TIONS mentioned throughout this
guide which are pertinent to the
item being checked. When compo-
nent conditions seem less than
satisfactory, replace with genuine
BOMBARDIER parts or approved
equivalents.

lmo2000-003a.book Page 78 Tuesday, December 21, 1999 3:27 PM

«
...
78
79
80
81
82
...
»

Содержание 2000 Islandia





























































































Отзывы:

Нет отзывов

Похожие инструкции для 2000 Islandia

Бренд: Hunter Страницы: 164

Бренд: 3D Tender Страницы: 18

Бренд: Gumotex Страницы: 40

Бренд: Marine Revolution Страницы: 12

Wakesetter 20VTX 2019

Бренд: Malibu Boats Страницы: 238

Herreshoff NY 30

Бренд: Sail Classics Страницы: 2

Бренд: Yamaha Страницы: 4

Бренд: Walker Bay Страницы: 18

Бренд: Weta Marine Страницы: 19

Бренд: UpRoar Страницы: 31

Бренд: Sea Eagle Boats Страницы: 16

PaddleSki 395ps

Бренд: Sea Eagle Страницы: 9

Бренд: Sea Eagle Страницы: 13

Бренд: Sea Eagle Страницы: 14

Stealth Stalker STS10

Бренд: Sea Eagle Страницы: 18

Бренд: Sea Eagle Страницы: 15

Бренд: Sea Eagle Страницы: 15

Бренд: Sprint Boats Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды