Sea-doo 2000 Islandia Скачать руководство пользователя | Manualshive

Страница: 7 / 92

background image

5

FOREWORD

The

Operator’s Guide and Safety

Handbook have been prepared to ac-
quaint the owner/operator or passen-
ger with this personal craft and its var-
ious controls, maintenance and safe
riding instructions. Each is indispens-
able for the proper use of the product,
and should be kept in a waterproof bag
with the craft at all times.

For any questions pertaining to the
warranty and its application, consult
the WARRANTY section in this guide,
and/or an authorized SEA-DOO dealer.

The information contained in this guide
should always be used in conjunction
with the information included in

Mer-

cury Marine (M

2

) Jet Drive Operator’s

Guide.

This guide uses the following symbols
to emphasize particular information.

CAUTION:

Denotes an instruction

which, if not followed, may damage
the craft and/or components.

NOTE:

Indicates supplementary infor-

mation needed to fully complete an in-
struction.

Although the mere reading of such in-
formation does not eliminate the haz-
ard, the understanding and application
of the information will promote its cor-
rect use.

The information and components/
system descriptions contained in this
guide are correct at the time of publi-
cation. Bombardier Motor Corporation
of America (B.M.C.A.) however, main-
tains a policy of continuous improve-
ment of its products without imposing
upon itself any obligation to install
them on products previously manufac-
tured.

Because of our ongoing commitment
to product quality and innovation,
Bombardier reserves the right at any
time to discontinue or change specifica-
tions, designs, features, models or
equipment without incurring obligation.

The illustrations in this document show
the typical construction of the different
assemblies and may not represent the
full detail or exact shape of the parts.
However, they represent parts that
have the same or similar function.

It is understood that this guide may be
translated into another language. In
the event of any discrepancy, the En-
glish version shall prevail.

Specifications are given in the SI met-
ric system with the SAE U.S. equiva-
lent in parenthesis. Where precise ac-
curacy is not required, some conversions
are rounded off for easier use.

A

Sea-Doo Sport Boat Shop Manual

can be obtained for complete service,
maintenance and more repair informa-
tion.

m

WARNING

Identifies an instruction which, if
not followed, may cause serious
personal injuries including the
possibility of death.

lmo2000-003a.book Page 5 Tuesday, December 21, 1999 3:27 PM

«
...
5
6
7
8
9
...
»

Содержание 2000 Islandia





























































































Отзывы:

Нет отзывов

Похожие инструкции для 2000 Islandia

Cross 57 Bow Rider

Бренд: YAMARIN Страницы: 51

Бренд: Dagger Страницы: 16

Бренд: RedShark Bikes Страницы: 36

Performance 342

Бренд: Baja Страницы: 85

Бренд: Baja Страницы: 82

Бренд: Lalizas Страницы: 18

Бренд: Zodiac Страницы: 27

Бренд: MACGREGOR Страницы: 28

Бренд: LaserPerformance Страницы: 10

Classic Big Game

Бренд: Ocean Kayak Страницы: 1

Бренд: NW Explorations Страницы: 61

Бренд: NW Explorations Страницы: 72

Бренд: Sea Ray Страницы: 110

Бренд: Sea Ray Страницы: 188

Бренд: SEATTLE Sailing Club Страницы: 8

330 Sport Bridge

Бренд: Silverton Страницы: 161

Бренд: Silverton Страницы: 207

Бренд: Silverton Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды