Sea-doo 2000 Islandia Скачать руководство пользователя | Manualshive

Страница: 78 / 92

background image

76

Docking Light

Gently pull headlight cover to detach it
from body. See

here-

inbefore

Remove light from its support.

Remove black metal cap on the back
of the light held in place by two screws.

Remove burnt bulb and replace with
new one.

CAUTION:

Never touch glass por-

tion of an halogen bulb with bare
fingers, it shortens its operating life.
If glass is touched, clean it using iso-
propyl alcohol which will remove
film from bulb surface.

The assembly is the reverse of remov-
al procedure.

Changing Room Light

Gently pull cover out and then replace
bulb.

General Inspection and
Cleaning

Inspection

Check engine compartment for any
damage. Ensure all hose clamps are
properly secured and no hose is
cracked, kinked or presenting any oth-
er damage.

Inspect muffler, battery, fuel tank and
oil reservoir fastening devices. Visually
check electrical connections for corro-
sion and tightness.

Inspect hull and jet pump water intake
grate for damage. Replace or have
damaged parts repaired.

Cleaning

The bilge should be cleaned by the deal-
er to remove any possible fuel/oil/
electrolyte deposits and mildew.

Occasionally, wash the body with hot
water and soap (only use mild deter-
gent). Remove any marine organisms
from engine and/or hull. Apply non-
abrasive wax.

CAUTION:

Never clean fiberglass

and plastic parts with strong deter-
gent, degreasing agent, paint thin-
ner, acetone, etc.

Wash windscreen with Bombardier
cleaner or equivalent (P/N 293 110 001
— 400 g) and water. For fine scratches
and scuff marks removal, use a wind-
shield polisher for acrylic, lucite, poly-
carbonate and similar materials.

Stains may be removed from seats, fi-
berglass and convenience center top
surface with Knight’s Spray-Nine*
from Korkay System Ltd or the equiv-
alent.

Respect the environment by ensuring
fuel, oil or cleaning solutions do not
drain into the waterways.

m

WARNING

If any gasoline leak and/or odors
are present, do not start the en-
gine. Have the craft serviced by
an authorized Sea-Doo dealer.

lmo2000-003a.book Page 76 Tuesday, December 21, 1999 3:27 PM

«
...
76
77
78
79
80
...
»

Содержание 2000 Islandia





























































































Отзывы:

Нет отзывов

Похожие инструкции для 2000 Islandia

Бренд: Anacortes Yacht Charters Страницы: 22

Бренд: J/Boats Страницы: 67

Бренд: Sea Eagle Страницы: 13

Бренд: Feathercraft Страницы: 8

Invitation Triss Racer

Бренд: BOMBARDIER Страницы: 23

Бренд: Highfield Страницы: 29

Бренд: Kingfisher Страницы: 69

Бренд: Laser Performance Страницы: 18

Бренд: Everglades Страницы: 126

Бренд: Nacra Страницы: 69

Бренд: Jeanneau Страницы: 97

Бренд: ISLAND PACKET Страницы: 8

Бренд: Quicksilver Страницы: 53

Бренд: Grand Страницы: 19

Бренд: MACGREGOR Страницы: 28

Бренд: Tayana Страницы: 112

Бренд: Everglades Страницы: 164

Бренд: Grady-White Boats Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды