manualshive.com logo in svg

Sea-doo 2000 Islandia, Руководство оператора

Поделиться
Скачать
Sea-doo 2000 Islandia Скачать руководство пользователя страница 52

50

58) Retractable Ladder(s)

LIFT LADDER COVER UNTIL STOPPED BY 
RETAINING SPRING (SPRING NOT SHOWN)

GENTLY PULL LADDER

FULLY EXTEND LADDER

CAUTION:

In order to avoid damage

to the ladders, they should not be
used when the boat is out of the wa-
ter.

To store ladder, completely retract it to-
ward front.

To close cover, gently push on the side
of the spring to release it and lower the
cover.

59) Mooring Cleat(s)

When mooring to a dock, it is recom-
mended to secure with cleats. The use
of dock lines with sealed air fenders is
recommended to protect your craft.

CAUTION:

Never use mooring cleats

to pull or lift the craft.

m

 WARNING

Engine should be OFF when us-
ing ladder. Keep limbs away from
jet or intake grate. Stay on center
of the ladder. Only one person at
the time on the ladder. Never use
the ladder for pulling, towing,
diving or jumping, boarding a
craft that is out of water or any
other purpose other than a ladder.

F14L1HY

F14L1IY

F14L1JY

lmo2000-003a.book Page 50 Tuesday, December 21, 1999 3:27 PM

Содержание 2000 Islandia





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды