Sea-doo 2000 Islandia Скачать руководство пользователя | Manualshive

Страница: 27 / 92

background image

25

COMPONENTS FUNCTIONS

1) Safety Lanyard

The safety lanyard cap should be se-
curely snapped onto its switch to be
fully operational.

Pulling the safety lanyard cap from the
switch stops the engine operation. At-
tach the safety lanyard to the opera-
tor's Personal Flotation Device (PFD)
and snap the cap to the switch to be
able to start the engine.

TYPICAL

1. Safety lanyard
2. Secure to PFD
3. Snap to safety lanyard switch

2) Steering Wheel

The steering wheel controls the direc-
tion of the craft. Turning the steering
wheel clockwise steers the craft to the
right and inversely.

Low-Speed Steering Control
System

Whenever the throttle lever is in

idle

position

and the steering wheel is ap-

proaching the end of its rotation, the
engine speed will be slightly acceler-
ated to increase the jet pump thrust
and thus improving the steering con-
trol for low speed operation and
when approaching/leaving a dock.
Refer to OPERATING INSTRUCTIONS
for more details.

3) Throttle Lever

When pushed forward craft acceler-
ates. When fully pulled back, engine
return to idle speed and the craft is
gradually stopped by water drag.

NOTE:

To activate throttle lever, shift

lever must be in forward or reverse po-
sition.

m

WARNING

Should the safety lanyard cap be-
come loose or fails to remain on
its switch, replace it immediately.

m

WARNING

Directional control is reduced with
decreasing speed and lost when
engine is off. Always disconnect
safety lanyard when craft is not in
operation.

m

WARNING

Do not lubricate the safety lanyard
switch.

F09L06Y

1

2

3

m

WARNING

While engine can be stopped us-
ing the ignition switch, good driv-
ing habits recommend that the
safety lanyard also be discon-
nected when stopping.

m

WARNING

Check steering and correspond-
ing steering nozzle operation be-
fore starting.

m

WARNING

Check throttle lever operation be-
fore starting the engine.

lmo2000-003a.book Page 25 Tuesday, December 21, 1999 3:27 PM

«
...
25
26
27
28
29
...
»

Содержание 2000 Islandia





























































































Отзывы:

Нет отзывов

Похожие инструкции для 2000 Islandia

Bravura 21 Series

Бренд: Supra Страницы: 90

Jeanneau International 50

Бренд: Sienne Страницы: 16

foundation series

Бренд: Quickboats Страницы: 22

Бренд: Woosung Страницы: 2

Бренд: K.R. Skentelbery & Sons Страницы: 16

Бренд: AKONA Страницы: 12

CAP CAMARAT 8.5 CC

Бренд: Jeanneau Страницы: 91

Бренд: Feathercraft Страницы: 23

Бренд: Malibukayaks Страницы: 27

Бренд: Crivit Страницы: 42

Бренд: Yamaha Страницы: 118

Бренд: LaserPerformance Страницы: 10

Бренд: J-80 Страницы: 25

Бренд: CORRECT CRAFT Страницы: 84

Бренд: Sea Ray Страницы: 46

Бренд: Sea Ray Страницы: 44

Бренд: Sea Ray Страницы: 158

Бренд: RS SAILING Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды