Sea-doo 2000 Islandia Скачать руководство пользователя

Страница: 33 / 92

BATTERY SWITCH

NOT PRESSED

PRESSED

Engine

OFF

• LED will continue to flash for 5

minutes.

• Buzzer will continue to sound for

5 minutes.

After 5 minutes:

• LED will stay on for 5 minutes

with the buzzer off.

• Every 30 seconds the buzzer will

come on and the LED will go off
for 1 second as a reminder.

After 10 minutes:

• LED and buzzer will go off.

• LED will stay on for 5 minutes

with buzzer off.

• Every 30 seconds buzzer will

come on and the LED will go off
for 1 second as a reminder.

• Second switch press will termi-

nate reminder cycle.

Engine

• LED will flash and buzzer will

sound, until voltage rises above
minimum required for 5 seconds.

• Every 30 seconds buzzer will

come on and the LED will go off
for 1 second as a reminder.

Ignition

• Both LED’s will come on. After this start up routine the unit immediately

begins monitoring the fuel level and the voltage condition.

Special

• In the event of low fuel and low voltage, both LED’s will come on with

a continuous warning beep. Pressing either switch will cause the non-
pressed switch to blink accompanied by a matching warning beep.

• Second switch press will turn off the buzzer with both LED’s blinking

alternately. Once voltage rises above minimum required unit will revert
to the last active low fuel condition.

FUEL SWITCH

NOT PRESSED

PRESSED

Engine

OFF

N.A.

Engine

• LED will flash and buzzer will

sound until ignition is turned off.

• LED will stay on with the buzzer

off.

• Every 30 seconds the buzzer will

come on and the LED will go off
for 1 second as a reminder.

• Second button press will termi-

nate reminder cycle.

Ignition

• Both LED’s will come on. After this start up routine the unit immediately

begins monitoring the fuel level and the voltage condition.

Special

• In the event of low fuel and low voltage, both LED’s will come on with

a continuous warning beep. Pressing either switch will cause the non-
pressed switch to blink accompanied by a matching warning beep.

• Second switch press will turn off the buzzer with both LED’s blinking

alternately. Once voltage rises above minimum required unit will revert
to the last active low fuel condition.

lmo2000-003a.book Page 31 Tuesday, December 21, 1999 3:27 PM

Содержание 2000 Islandia





























































































Результаты поиска

Содержание 2000 Islandia

Отзывы:

Похожие инструкции для 2000 Islandia

Бренды по названию

Популярные бренды

Sea-doo 2000 Islandia, Руководство оператора

Результаты поиска

Содержание 2000 Islandia

Отзывы:

Похожие инструкции для 2000 Islandia

Бренды по названию

Популярные бренды