manualshive.com logo in svg

Sea-doo 2000 Islandia, Руководство оператора

Поделиться
Скачать
Sea-doo 2000 Islandia Скачать руководство пользователя страница 41

39

TYPICAL

Step

: Pull latch and lift cover

Lift the latch ring and open cover gen-
tly until stopped by retaining spring.

To close, gently push on the side of the
spring to release it and lower the cover.

TYPICAL

1. Gently push here to release the spring

31) Rear Storage 

Compartment

Convenient rear storage location to be
used to carry large personal articles.
Ideal location for wakeboards, knee-
boards, spare Personal Flotation De-
vice (PFD) etc.

To open engine cover, open the rear
side storage compartment panel and
pull lever, as shown in the next photo.

CAUTION:

To avoid damage, driver

seat must be rotated to forward po-
sition before opening engine cover.

1. Pull this lever

The gas assist cylinders will complete
the opening and hold engine cover
open.

NOTE:

Unauthorized access to the

rear storage compartment is prevent-
ed only when the rear side storage
compartment is locked.

Firmly close engine cover to relatch.

m

 WARNING

Never operate the craft with the
storage compartment cover open.

F04L0QZ

1

1

F10L1EY

1

m

 WARNING

When engine cover is lifted, nev-
er touch any electrical part when
starting engine or while in opera-
tion. Never leave any object, rag
or tool in the engine compart-
ment or in the bilge.

m

 WARNING

Never operate the craft with the
engine cover open. 

F14L0PY

1

lmo2000-003a.book Page 39 Tuesday, December 21, 1999 3:27 PM

Содержание 2000 Islandia





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды