Sea-Bird Scientific OCR-504 Скачать руководство пользователя | Manualshive

Страница: 19 / 64

background image

Operation Manual

SYSTEM

OCR-504 Multispectral Radiometer

SECTION

C - START UP

I

MPORTANT! Both the RS-232 and RS-422 telemetry interfaces transmit

the  same  information.  The  RS-232  interface  provides  bi-directional
communication while  the RS-422 is transmit-only. Normally, the RS-232
interface is used for configuring and testing your instrument. The RS-422
interface  would  normally  be  used  for  telemetry  acquisition  in  the  field
using  longer  cables.  Most  computer  serial  interfaces  are  RS-232.
Therefore,  if  you  are  using  the  RS-422  interface  on  the  instrument,  a
converter  will  be  required  to  convert  the  output  from  the  instrument  to
levels compatible with your computer. In most cases, only one of these
telemetry interfaces is provided on a cable.

C

ONNECTING THE

C

OMPONENTS

When making connections, proper alignment on the connector pins is critical to
avoid damage. Visually ensure that the pins on the male connectors are
properly aligned with (and partially seated into) the sockets on their female
counterparts before pushing them together for final connection. Finally, ensure
that the locking sleeve or locking strap is securely fastened after connection.

The following is a generic step-by-step procedure for setting up your OCR-504
Multispectral Radiometer. You may use this procedure with any Sea-Bird
Scientific approved interface cable:

1. Ensure that, initially, the instrument is completely disconnected from the

power supply.

2. Ensure that the power supply is setup for the proper voltage.

3. If possible, turn off the power supply.

4. Mount the instrument in the desired position.

5. Connect the instrument side of the interface cable to the bulkhead on the

instrument.

6. Connect the telemetry-output side of the interface cable to the serial

interface of the computer. Use an appropriate level converter if needed.

7. Configure any software for use with the instrument.

8. Remove the protective cover from the end of the OCR-504.

9. Connect the power-input side of the interface cable to the power supply.

10. Apply power to the instrument (turn on the power supply).

Once  your  OCR-504  has  been  properly  connected  and  power  has  been
applied, an initialization sequence will begin automatically to ready the device
for  normal  operation.  This  sequence  takes  approximately  4  seconds  to
complete.  Once  finished,  the  instrument  should  begin  normal  operation.  See
the

Conducting a Telemetry Test

section below to make sure that your

instrument is working properly. If this does not happen, remove power from the
instrument and repeat the connection sequence. If you are still experiencing
problems, contact a Sea-Bird Scientific customer service representative for
assistance.

See section

D - OPERATION

for more information on operating your

instrument.

«
...
17
18
19
20
21
...
»

Содержание OCR-504

































































Отзывы:

Нет отзывов

Похожие инструкции для OCR-504

Бренд: Magnetic Instrumentation Страницы: 63

Бренд: Accu-Chek Страницы: 12

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: Macnaught Страницы: 4

Бренд: Mahr Страницы: 384

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 4

Бренд: Velleman Страницы: 8

Бренд: velocomp Страницы: 4

Бренд: Hanna Instruments Страницы: 28

Бренд: Keysight Страницы: 66

SPEEDLOADER BRIDGE SYSTEM

Бренд: Floyd Rose Страницы: 10

Бренд: Major tech Страницы: 16

Бренд: Reed Instruments Страницы: 12

Бренд: iSTEK Страницы: 15

Бренд: ERICHSEN Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды