1982-1996 Buick Century
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Remove the four screws from under the top
edge of the instrument cluster trim piece.
2. Remove the three screws and the two 7mm hex screws from below the instrument cluster trim piece.
3. Remove the three screws and the rocker-switch trim to the right of the instrument cluster. Pull f rmly to
remove the rocker-switch trim.
"A1" BRACKET USE
NOTE:
For cars equipped with a
HOLE #1
LEFT SIDE
RIGHT SIDE
"B1" BRACKET
column mounted shift lever, position
"A1" SOPORTE USA
LADO IZQUIERDA
LADO DERECHO
USE HOLE #2
the lever in low gear for additional
clearance.
ABERTURA NO. 1
"B1"
SOPORTE
USA
4. Remove the instrument cluster
trim
piece.
TRIM
BRACKET
ABERTURA
NO. 2
5. Remove the four screws from
the radio brackets, pull the radio
CORTA EL
SOPORTE
out of the cavity, then disconnect
the antenna, speaker leads
and all the electrical connections.
Remove the radio.
"A2" BRACKET USE
HOLE #1
"A2" SOPORTE USA
ABERTURA NO. 1
FRONT OF KIT
FRENTE DE ESTUCHE
"B2" BRACKET
USE HOLE #2
"B2" SOPORTE
USA ABERTURA NO. 4
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1985-90 Buick Electra/Park Avenue
Read pages 3-6
for kit assembly.
1986-91 Buick Le Sabre
RADIO REMOVAL:
1. Carefully snap off the trim from around the air-conditioning controls.
2. Remove the four screws from behind the trim piece.
"B1" BRACKET
USE HOLE #2
3. Slide the radio trim panel to the
"A1" BRACKET USE
"B1" SOPORTE
left (driver’s side) of the car and
HOLE #1
LEFT SIDE
RIGHT SIDE
USA ABERTURA
"A1" SOPORTE USA
LADO IZQUIERDA
LADO DERECHO
NO. 2
remove
it.
ABERTURA NO. 1
4. Remove the four screws which
secure the radio to the dashboard,
TRIM
BRACKET
slide the radio out of the cavity
CORTA EL
and disconnect the antenna,
SOPORTE
speaker leads and all the
electrical supply harnesses.
Remove the radio.
"D2" BRACKET USE
"B2" BRACKET
HOLE #1
USE HOLE #2
FRONT OF KIT
"D2" SOPORTE USA
FRENTE DE ESTUCHE
"B2" SOPORTE
ABERTURA NO. 1
USA ABERTURA NO. 4
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1984-87 Buick Regal
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Remove the radio trim panel by carefully prying outward
evenly around the edges.
2. Remove the four screws securing the radio mounting bracket to the dash. Pull the assembly out of the
cavity to gain access to the wiring.
3. Disconnect the antenna and all the electrical connections, then remove the radio.
"A1" BRACKET USE HOLE #3
LEFT SIDE
RIGHT SIDE
"A1" BRACKET USE HOLE #3
"A1" SOPORTE USA ABERTURA NO. 3
LADO IZQUIERDA
LADO DERECHO
"A1" SOPORTE USA ABERTURA NO. 3
FRONT OF KIT
"C2" BRACKET USE HOLE #3
"B2" BRACKET USE HOLE #3
"C2" SOPORTE USA ABERTURA NO. 3
FRENTE DE ESTUCHE
"B2" SOPORTE USA ABERTURA NO. 3
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
7