1987-91 Pontiac Bonneville
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Place the gear selector in low gear to gain clearance.
2. Gently pull on the edges of the radio panel to release
the panel clips and remove the panel.
SPACER
EL ESPACIO
3. Remove the two screws from
"D2" BRACKET
the bracket above the radio.
USE HOLE #2
CUT OFF PINS (TWO SPACERS)
CORTA LAS CLAVIJAS
"D2" SOPORTE USA
4. Remove one screw from the
(DOS ESPACIADORES)
ABERTURA NO. 2
rear support bracket (access
through the ashtray cavity).
SPACER
EL ESPACIO
5. Insert a thin blade screwdriver
into the two slots below the
"B2"
BRACKET
radio and pry the metal
USE HOLE #2
retaining tabs upward
"B2" SOPORTE
TOP
USA ABERTURA
TOPE
NO. 2
to release them.
6. Slide the radio out of the cavity,
CUT OFF TABS
disconnect all the electrical
(TWO BRACKETS)
connections, then remove the radio.
ROMPE LAS
LENGUETAS (DOS
SOPORTES)
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1984-88 Pontiac Fiero
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Remove the four screws from the radio trim panel.
2. Pull the panel up and outward toward the right.
3. Remove the four screws from the radio brackets and pull the radio out of the cavity.
4. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
"A1" BRACKET USE HOLE #3
LEFT SIDE
RIGHT SIDE
"B1" BRACKET USE HOLE #4
"A1" SOPORTE USA
LADO IZQUIERDA
LADO DERECHO
"B1" SOPORTE USA ABERTURA
ABERTURA NO. 3
NO. 4
FRONT OF KIT
FRENTE DE
ESTUCHE
"C2" BRACKET USE HOLE #3
"D2" BRACKET USE HOLE #4
"C2" SOPORTE USA ABERTURA NO. 3
"D2" SOPORTE USA ABERTURA NO. 4
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1993-02 Pontiac Firebird
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Using a panel removal tool/screwdriver, carefully release
the fastening clips from around the perimeter of the radio
trim bezel and remove the bezel.
2. Extract the four screws securing the radio to the dash, pull the radio from the cavity, unplug all the
connectors, and remove the radio.
"B1" BRACKET USE HOLE #1
LEFT SIDE
RIGHT SIDE
"B1" SOPORTE USA ABERTURA
"A1" BRACKET USE HOLE #1
LADO IZQUIERDA
LADO DERECHO
"A1" SOPORTE USA
NO. 1
ABERTURA NO. 1
FRONT OF KIT
FRENTE DE
"C2" BRACKET USE HOLE #1
ESTUCHE
"B2" BRACKET USE HOLE #1
"C2" SOPORTE USA ABERTURA NO. 1
"B2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
25