1997-99 Chevrolet Venture
Read pages 3-6
for kit assembly.
1997-99 Oldsmobile Silhouette
1997-99 Pontiac Trans Sport
RADIO REMOVAL:
1. Open ashtray and extract one from lower right side of dash bezel.
2. Open 12V socket cover and extract one from lower left dash bezel.
3. Lift bottom of dash bezel out to allow top edge to unhook from under air vents, unplug lighter,
switches and remove dash.
4. Extract two 7mm hex head screws holding radio in, unplug connectors and remove radio.
"A1" BRACKET USE HOLE #2
"B1" BRACKET USE HOLE #2
"A1" SOPORTE USA
"B1" SOPORTE USA ABERTURA NO. 2
ABERTURA NO. 2
LEFT SIDE
LADO IZQUIERDA
RIGHT SIDE
LADO DERECHO
FRONT OF KIT
FRENTE DE
ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1992-95 Oldsmobile Achieva
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Extract the two screws from the bottom of the dash
bezel, below the radio and above the console pocket,
securing it to the dash.
CARRIAGE BOLT
PERNO DE PORTE
2. Extract the two screws above the instrument cluster.
3. Remove the two screws above the AC vent located in
the center of the dash.
BOTTOM
4. Pull the dash bezel out away from the dash and using
FONDO
a panel removal tool/screwdriver, carefully disconnect
the fastening clips securing the dash vents (the one in
the center and the one on the driver's side) to the bezel.
FLANGE NUT
TUERCO REBORDE
5. Disconnect all the connectors and slide the dash bezel
away from the dash towards the passenger side.
6. Extract the two 10mm bolts securing the radio to the dash, pull the
radio from the cavity, unplug all the connectors, and remove the radio.
SECURE THE KIT PANEL TO THE DASH USING THE SUPPLIED CARRIAGE BOLTS AND NUTS.
Asegure el panel estuche al tablero usando los pernos de porte y tuercos proveidos.
1985-91 Oldsmobile Cutlass Calais
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Open armrest and extract (2) Phillips head screws
BREAK OFF TAB
from bottom of pocket.
ROMPE LA LENGUETA
2. Remove pocket and extract (2) 10mm bolts from
underneath. Lift and slide armrest towards rear of car.
3. Extract (2) 7mm/t-15 bolts from rear edge of gear
select lever trim panel. Remove ashtray (on center
console) and extract (1) 7mm/t-15 bolt from underneath.
4. Put car in low gear. Lift and slide center console
towards rear of car
BOTTOM
FONDO
5. Gently unsnap and remove radio trim bezel.
"C1" BRACKET
6. Extract (2) 7mm/T-15 Torx screws securing
USE HOLE #5
"C1" SOPORTE
radio to the dash, unplug wiring, antenna,
USA ABERTURA NO. 5
"D1" BRACKET
USE HOLE #1
and remove radio.
"D1" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
21