1985-92 Pontiac Firebird
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
"A1" BRACKET USE HOLE #1
1. Carefully pull on the
"B1" BRACKET
"A1" SOPORTE USA ABERTURA
edges of the radio
NO. 1
USE HOLE #1
LEFT SIDE
RIGHT SIDE
"B1" SOPORTE
trim panel to release
LADO IZQUIERDA
LADO DERECHO
USA ABERTURA
NO. 1
the panel clips and
remove the panel.
2. Remove the four screws
which secure the radio
to the console.
3. Disconnect
the
antenna, speaker leads
FRONT OF KIT
TRIM
BRACKET
"C2" BRACKET
ESTUCHE
FRENTE DE
and all the electrical
connections,
then
"D2"
CORTA EL
USE HOLE #1
SOPORTE
"C2" SOPORTE USA ABERTURA NO. 1
remove the radio.
BRACKET USE HOLE #1
"D2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1996-98 Pontiac Grand Am
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Extract two screws from the dash bezel above instrument/gauges.
"B1" BRACKET
USE HOLE #1
2. Extract two screws from back of deep
LEFT SIDE
"B1" SOPORTE USA ABERTURA
storage pocket below the radio.
LADO IZQUIERDA
NO. 1
"C2" BRACKET
USE HOLE #5
3. Carefully pull out on the
instrument/radio panel to
"C2" SOPORTE USA
release snap clips, unplug
ABERTURA NO. 5
switches and remove bezel.
4. Extract three 7mm screws
securing radio, unplug
connectors, antenna lead,
FRONT
RIGHT SIDE
and remove radio.
OF KIT
LADO DERECHO
FRENTE DE
TRIM BRACKET
ESTUCHE
CORTA EL SOPORTE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1992-1995 Pontiac Grand Am
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Extract the screw from the underside of the radio trim bezel.
2. Extract the fve screws from the upper glove box securing
FLANGE NUT
the glove box assembly and remove the glove box.
TUERCO REBORDE
3. Open up the lower glove box and extract the three
screws securing the radio trim bezel near the pin switch.
4. Extract the three screws from below the steering column that
TOP
TOPE
secure the top of the driver's side lower dash.
5. Extract the fve screws securing the lower section
of the driver's side lower dash panel and remove the panel.
6. Extract the screw securing the radio trim bezel behind the driver's side lower dash panel.
7. Using a panel removal tool/screwdriver, carefully pry the
CARRIAGE BOLT
radio trim bezel outward to release and remove it.
PERNO DE PORTE
8. Remove the two nuts from below the radio cavity securing the radio to the dash,
pull the radio from the cavity, unplug the leads and remove the radio.
SECURE THE KIT PANEL TO THE SUB-DASH USING THE SUPPLIED CARRIAGE NUTS AND BOLTS.
Asegura el panel estuche al tablero-sub usando los tuercos y pernos de porte.
"G" BRACKET
1985-91 Pontiac Grand Am
SOPORTE "G"
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Unsnap the front edge of the gearshift
trim piece from the center console.
2. Gently pull on the radio trim panel
TOP
"F" BRACKET
to release the snaps and remove the trim.
TOPE
SOPORTE "F"
3. Remove the two screws which
secure the radio and slide the radio out of the cavity.
4. Disconnect the antenna, speaker leads and
all the electrical connections, then remove the radio.
SECURE THE KIT PANEL TO THE SUB-DASH USING THE SUPPLIED CARRIAGE NUTS AND BOLTS.
Asegura el panel estuche al tablero-sub usando los tuercos y pernos de porte.
26