1982-89 Oldsmobile Toronado
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Remove the fve screws from the top underside of the dash trim.
"B1" BRACKET
USE HOLE #2
2. Lower the tilt wheel and gently pull out on the trim piece from the
top side. This allows clearance to disconnect the electrical connections.
"B1" SOPORTE
Remove
the
"A1" BRACKET USE HOLE #1
USA ABERTURA
LEFT SIDE
RIGHT SIDE
"A1" SOPORTE USA
NO. 2
connections
LADO IZQUIERDA
LADO DERECHO
ABERTURA NO. 2
and the panel.
3. Remove the ten screws
securing the climate controls
and the radio, six screws
from the climate controls
and four screws from
the
radio.
4. Disconnect
the
FRONT OF KIT
antenna,
speakers,
FRENTE DE
and all the electrical
"B2"
ESTUCHE
connections
and
"A2" BRACKET
BRACKET
remove the radio.
USE HOLE #1
USE HOLE #2
"A2" SOPORTE USA ABERTURA NO. 1
"B2" SOPORTE USA ABERTURA NO. 2
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1989-93 Oldsmobile Touring Sedan
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Open the center console storage compartment, then remove
the two screws securing the storage sleeve/pocket.
Remove the sleeve/pocket insert.
2. Remove the two screws from the front edge of the console pocket
(at the wood trim), then remove the trim section.
3. Pop out and remove the electric seat control panel (located in the center console).
4. Carefully snap off the trim piece from around the gear
"C2" BRACKET USE HOLE #2
"D2" BRACKET
selector, then remove the four screws securing the
"C2" SOPORTE
USE HOLE #2
USA ABERTURA NO. 2
"D2" SOPORTE
wood trim to the console substructure.
USA ABERTURA
5. Remove the wood trim piece from the top of the console,
NO. 2
pull the trim piece back and
up to remove. Disconnect
the wire harnesses and
"A1" BRACKET
remove the trim piece.
USE HOLE #2
6. Extract the four screws
"A1" SOPORTE
USA ABERTURA
which secure the radio,
NO. 2
BOTTOM
pull the radio out of the
FONDO
cavity, disconnect the
wire harnesses and the
"B2" BRACKET USE HOLE #2
"B2" SOPORTE USA ABERTURA NO. 2
antenna, then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1992-99 Pontiac Bonneville
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Using a panel removal tool/screwdriver, carefully release
the fastening clips from around the perimeter of the radio
"B1" BRACKET
trim bezel and remove the panel.
USE HOLE #2
2. Extract
the
three
"A1" BRACKET USE HOLE #4
RIGHT SIDE
"B1" SOPORTE
LEFT SIDE
"A1" SOPORTE USA
LADO IZQUIERDA
LADO DERECHO
USA ABERTURA
screws
securing
ABERTURA NO. 4
NO. 2
the radio to the
dash, pull the radio
from the cavity,
unplug all the
connectors
and
remove the radio.
FRONT OF KIT
FRENTE DE
"A2" BRACKET
USE HOLE #2
ESTUCHE
"A2" SOPORTE USA ABERTURA NO. 2
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
24