Schlumbohm 110 0607 Скачать руководство пользователя страница 35

Страница: 35 / 44

Pilot²

Doc. No. 610 2221 v07

- 35 -

(*applicable with the ultrasonic extension module)

12.2.

Maintenance

You can find detailed information on the processing of individual components in chapter 18

(Cleaning, disinfection and sterilization) of the mentioned preparation instructions.

It is imperative that you follow the following instructions:

- Check the connection cable and plug connections every 6 months.

- If the wireless foot switch is not used for a long time, the batteries must be removed.

- Do not use rechargeable batteries for the foot switch (only batteries of type AAA with 1.5V).

- The EndoPilot² does not contain any components that can be repaired on the spot.

- Modifying or opening the device voids the warranty.

- Repairs may only be carried out by the manufacturer!

- Even for infrequent use, the device should be charged every 6 months.

- Only use the intended power supply unit!

- A battery change is planned after 4 years. Heavily aged batteries can pose a safety risk.

Caution: Only the manufacturer or an authorized partner may change the battery.

Caution!

The motor must not be lubricated or oiled under any circumstances! When

servicing the contra-angle, make sure that no lubricant or cleaning agents enter the

motor! Allow excess oil to drip out of the contra-angle before operation. For this

purpose, set the contra-angle down in a vertical position.

The contra-angle should be oiled with oil spray for contra-angles immediately after

application (before reprocessing) to remove penetrated treatment fluids such as sodium

hypochlorite.

Before operating the ultrasonic handpiece, check for damage to the insulation and check

whether the oscillator’s axis is firmly anchored in the housing before each application. Do not

use any damaged ultrasonic handpieces or cables.

Make sure that the connectors are dry.

12.3.

Transport

Prevent the device from falling. The device contains a lithium-ion battery (Li-Ion battery)

Power output: 48 Wh. A hard fall may lead to mechanical damage to the device and the

battery unit. The inserted battery may cause fires and injuries if handled incorrectly. The

device must not be heated up to above 60°C, burned, immersed in liquids or dismantled.

If possible, please use the manufacturer's packaging or sufficiently strong packaging for

shipping the device. Please follow the applicable shipping regulations.

Switch off the device prior to shipping and remove the microSD card. Enclose these in a

clearly visible way. Pack the unit so that the on/off switch on the rear side of the device cannot

be activated unintentionally during transport.

Ensure that all components are disinfected prior to shipping (see processing instructions in

chapter 18).

Dirty and contaminated products must not be shipped.

For shipment please follow the current transport regulations for equipment with Lithium-Ion-

Batteries (UN3481).

Содержание 110 0607













































Результаты поиска

Содержание 110 0607

Отзывы:

Бренды по названию

Популярные бренды

Schlumbohm 110 0607, Руководство пользователя

Результаты поиска

Содержание 110 0607

Отзывы:

Бренды по названию

Популярные бренды