Schlumbohm 110 0607 Скачать руководство пользователя страница 17

Страница: 17 / 44

Pilot²

Doc. No. 610 2221 v07

- 17 -

(*applicable with the ultrasonic extension module)

•

The ambient temperature must be within the prescribed limits.

(See chapter 16). Avoid heating up to above 60°C in any case!

•

The device must not be installed near free oxygen, flammable gas mixtures or

liquids (e.g. in operating theatre or emergency areas).

•

The EndoPilot² should not be installed near devices emitting electromagnetic

radiation so as not influence the correct length determination.

•

Place the foot switch in such a way that it will be easy to operate.

•

Make sure that the foot switch cannot be activated unintentionally.

•

Place the device in such a way that the power supply cable can be pulled out of the

device when necessary.

2.2.

Holders for the handpieces

The holders provide a safe position for the applied parts. Insert the retainer for the apex cable

laterally into the hole at right handpiece holder.

You can upgrade the device with additional functions (example: left arm with a holder for

DownPack and BackFill). For the assembly of additional holders as well as for the

arrangement of the handpieces, please follow the assembly instructions provided separately.

*Ultrasonic module: A double holder is mounted on the extension module for the ultrasonic

handpiece and the motor.

2.3.

Connection

All connections are plugged in and must

not

be twisted! Care must be taken to ensure that

the plug’s groove fits into the socket’s groove. The ‘Push and Pull’ connections for the

handpieces are color-coded (the numbers refer to the illustrations on the inside cover page).

Figure

Connection Use

blue

Motor

green

Apex cable, connection to the patient (lip clip)

black

Power supply unit

Slot

microSD card

red

BackFill gun, optional

blue

D-Pack, optional, please do not insert the motor here!

Insert the EndoPilot² microSD card into the SD slot before first use.

(Insert the card carefully, do not use sharp tools).

*Ultrasonic module: The ‘Push and Pull’ connections for the handpieces are color-coded as

for the EndoPilot²:

Figure

Connection Use

16a

grey

Ultrasonic handpiece cable and ultrasonic handpiece

When connecting the ultrasonic handpiece to the ultrasonic cable, ensure that the handpiece

is not twisted during connection. If the EndoPilot² control unit is not already equipped with

the ultrasonic module, it can be done later. The device can be upgraded in the factory. Your

dealer will advise you how to reship the device.

Содержание 110 0607













































Результаты поиска

Содержание 110 0607

Отзывы:

Бренды по названию

Популярные бренды

Schlumbohm 110 0607, Руководство пользователя

Результаты поиска

Содержание 110 0607

Отзывы:

Бренды по названию

Популярные бренды