SBS SB-1000 Скачать руководство пользователя страница 38

Страница: 38 / 38

SBS System – SB-1000 Operation

Appendix B: Replacement Parts List

Part#

Description

Balancer/ RPM Sensor Cables

SB-1800

RPM Proximity Sensor

SB-1816

RPM Sensor Cable – 5m/ 16ft

SB-1916

RPM Sensor Extension Cable – 5m/ 16ft

SB-1932

RPM Sensor Extension Cable – 10m/ 32ft

SB-48xx

Balancer Cable /SB-5500 series

SB-48xx-V

Balancer Cable /SB-5500 series – Heavy Duty

SB-46xx

Balancer Extension Cable /SB-5500 series

CA-0121

12-pin Male DIN (control end plug of Balancer Cable for 48xx series cables)

CA-0125

Standard 7-Pin Female Bayonet Connector (Balancer end of Balancer Cable)

CA-0105

Heavy-Duty 7-Pin Female Bayonet Connector (Balancer end of Balancer Cable)

Vibration Sensors

SB-14xx

Sensor Cable (standard lengths)

SB-16xx

Sensor Ext. Cable (standard lengths)

Control Options

SK-5000

Rack Panel: SB-5500, Full Wide w/ 1/2 Blank, 3U

SK-5001

Rack Panel: SB-5500, Partial Wide 3U w/ Handles

SK-5002

Rack Panel: SB-5500, 1/2 Rack 3U Bracket

SK-5005

Keypad Mount: Flush Panel Frame Kit

SB-24xx-L

Hardwire Interface cable (standard lengths)

Other Parts

SB-8510-V

Complete Heavy-Duty SBS Balancer Low Profile Collector replacement

SB-8520

Collector Slip Ring Block Replacement

SB-8530

Collector Slip Ring Post Replacement

SB-1300

Adjustable Hook Pin Spanner (Adapter Flanges)

SB-1321

Adjustable Face Pin Spanner 3/8” pins (Large Adapter Nuts)

xx in P/N = cable length in feet

Standard options 11 [3.5m], 20 [6.0m], or 40 [12.0m], e.g. SB-4811 = 11ft [3.5m]

Support

For support, contact the machine builder or SBS at:

Accretech SBS, Inc.

2451 NW 28th Avenue

Portland, Oregon 97210 USA

Tel.: +1 503.227.7908

Fax: +1 503.223.1258

[email protected]

https://accretechsbs.com/

Содержание SB-1000







































Результаты поиска

Содержание SB-1000

Отзывы:

Похожие инструкции для SB-1000

Бренды по названию

Популярные бренды

SBS SB-1000, Руководство по эксплуатации

Результаты поиска

Содержание SB-1000

Отзывы:

Похожие инструкции для SB-1000

Бренды по названию

Популярные бренды