Sapling NTP 8000 Series Скачать руководство пользователя страница 62

Страница: 62 / 76

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Web Interface - Email Alerts

1. Email Recipient -

This field is where the user name of the e-mail recipient is entered. Do not enter the

domain and suffix. If the full address is [email protected], then johnsmith should be entered in this field.

2. Email Domain -

This field is where the user enters the domain name of the email recipient. Do not

enter the user name or the @. If the full address is [email protected], then domain.com should be

entered in this field.

3. Email Server -

This field is where the user enters the address of the local outgoing email server for the

email recipient. Consult with the network administrator for the email server address. Emails are sent using

SMTP.

4. NTP Synchronization Timeout -

When the box is checked, the master clock checks the amount of

time since the last NTP signal has been received. If the amount of time recorded exceeds the amount of

time specified in the box to the right, then the master clock sends an email alert. If this option is selected,

the value in the box should be 1 or higher.

5. GPS Synchronization Timeout -

When the box is checked, the master clock tests the internal GPS

module to confirm that it is receiving a valid time signal from the GPS antenna. If the module fails the

check for an amount of time exceeding the value specified in the box to the right, then the master clock

sends an email alert. If this option is selected, the value in the box should be 1 or higher.

6. Master Restart -

When the box is checked, the master clock sends an email alert every time that it is

restarted (including after power loss or deactivation by the user).

7. Fire Alarm -

When the box is checked, the master clock sends an email whenever the master clock

receives a signal that the fire alarm has been activated. The fire alarm must be properly wired to the master

clock for this to work. For wiring instructions, refer to the section of this manual labeled “Inputs - Sync-

Wire: Fire Alarm Interface Installation.”

8. Submit -

When the button is clicked on, all of the settings on the page are saved and applied.

9. Test Send -

When the button is clicked on, the master clock will send an email to whichever address

has been entered. It does NOT save the settings.

1
2

Содержание NTP 8000 Series













































































Результаты поиска

Содержание NTP 8000 Series

Отзывы:

Похожие инструкции для NTP 8000 Series

Бренды по названию

Популярные бренды

Sapling NTP 8000 Series, Руководство по установке

Результаты поиска

Содержание NTP 8000 Series

Отзывы:

Похожие инструкции для NTP 8000 Series

Бренды по названию

Популярные бренды