Saphire Scientific 370 SS Скачать руководство пользователя страница 11

Страница: 11 / 81

SECTION 1

SAPPHIRE SCIENTIFIC MODEL 370 SS

PART#

49-038 REV F

INSTALLATION

REQUIREMENTS

Prior to beginning the installation, read the

ENTIRE “Installation” section of this manual.

Since the

MODEL 370 SS

Truck mount unit

weighs (with waste tank and accessories)

approximately 970 lbs., please adhere to the

following recommendations prior to installing

the unit.

1. The unit should

NOT

be installed in any

motor vehicle rated less than ½ ton capacity.

The console and waste tank with accessories

must NOT exceed the vehicle’s axle weight

limit.

2. If mounting the unit in a trailer, ensure that

the trailer is rated for the total weight of the

unit

and trailer.

Electric or hydraulic brakes must

be provided, and strict compliance with all State

and Federal laws must be maintained.

3. If mounting in a trailer, the

MODEL 370 SS

console must be positioned so that it balances

properly with respect to the trailer axle. Ten

percent (10%) of the unit’s total overall weight

(w/o accessories or water) should be on the

tongue. This unit has an air cooled engine, and

adequate ventilation must be provided to

prevent overheating.

4. The vehicle tires must have a load rating in

excess of the combined unit and vehicle weight.

SAPPHIRE SCIENTIFIC

does not

recommend using any type of flooring materials

that absorb water. This condition will result in

rust and corrosion of the vehicle floor.

6. Insulation under rubber mats should be

removed prior to installation of the unit.

FUEL REQUIREMENTS

Use unleaded fuel ONLY.

Use only fresh,

clean unleaded gasoline with a minimum octane

rating of 87.

Do Not

use high octane gasoline.

Gasoline with up to, not exceeding, 10% ethanol

is acceptable.

NOTE:

Using other gasoline/alcohol blends

including E20 and E85 will cause damage to

engine components and will void warranty.

ENGINE OIL REQUIREMENTS

Use high-quality oil of at least API (American

Petroleum Institute) service class SG, SH, SJ or

higher.

Do not use additives.

High quality 30W

oil is recommended. A 10-30 synthetic blend

may be used after 50 hours of operation for a

new or rebuilt engine to allow the piston rings to

properly seat. It is never recommended to

extend oil change intervals past 100 hours.

Engine oil capacity

1.7 L

1.8 US qts

Tightening torque

Drain Plug

13.6 N·m

1.4 kgf·m

10.0 lbf·ft

NOTE:

Using lower service class oil or

extending oil change intervals longer than

recommended can cause engine damage.

Содержание 370 SS


















































































Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды

Saphire Scientific 370 SS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды