Saphire Scientific 370 SS Скачать руководство пользователя страница 2

Страница: 2 / 81

SAPPHIRE SCIENTIFIC MODEL 370 SS

PART#

49-038 REV F

Congratulations

on your purchase of the

MODEL 370 SS

Truck mount cleaning

unit. This instruction/parts manual is a

guide for operating and servicing your

SAPPHIRE SCIENTIFIC

Truck mount

unit.

Proper operation and service are necessary to

ensure the outstanding performance of this unit.

When properly maintained, your Truck mount

will have a long and trouble-free life.

The following service methods outlined in this

manual are detailed in a manner that operation

and servicing may be performed properly and

safely. Because service levels vary due to the

skill of the mechanic, tools and parts

availability, ensure that prior to attempting any

repair, you are familiar with this equipment and

have the proper tools. Any questions regarding

the operation, service, or repair of this unit

should be directed to your nearest

SAPPHIRE

SCIENTIFIC

dealer.

The headings

WARNING

and

CAUTION

are

utilized to warn you that steps must be taken to

prevent personal injury or damage to the

equipment. Please make sure that you have read

and understand these instructions entirely before

proceeding with the operation of this unit.

THIS UNIT MUST BE INSTALLED BY

THE DEALER THAT YOU PURCHASED

IT FROM IN ACCORDANCE WITH THE

SAPPHIRE SCIENTIFIC INSTALLATION

PROCEDURES.

BE SURE TO FILL OUT THE WARRANTY

CARD ONLINE AT WWW.

SAPPHIRE

SCIENTIFIC

.COM

Record your units serial number here for future

reference or if you should need to contact the

factory in the future for any reason.

S/N:

This service and operations manual is written

specifically for

SAPPHIRE SCIENTIFIC

MODEL 370 SS

Truck mount Cleaning units

manufactured by:

SAPPHIRE SCIENTIFIC

2604 Liberator

Prescott, AZ 86301

USA

The information contained in this document is

subject to change without notice and does not

represent a commitment on the part of

SAPPHIRE SCIENTIFIC.

No part of this

work may be used or reproduced in any form or

means without the express written consent and

permission of

SAPPHIRE SCIENTIFIC.

Published by

SAPPHIRE SCIENTIFIC.

First printing: May 2009

Revised: August 2010; Rev A

November 2010; Rev B

January 2012; Rev C

June 2012; Rev D

November 2012; Rev E

July 2014; Rev F

Printed in USA

MODEL 370 SS

MANUAL

PART# 49-038

Содержание 370 SS


















































































Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды

Saphire Scientific 370 SS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды