Saphire Scientific 370 SS Скачать руководство пользователя страница 81

Страница: 81 / 81

SECTION 5

SAPPHIRE SCIENTIFIC MODEL 370 SS

PART#

49-038 REV F

Fuel Supply & Return Line Installation (Underneath the Vehicle Floor)

Refer to the transfer flow kit instructions found with the appropriate kit for your vehicle.

Connect the fuel line from the transfer flow kit to the inlet side of the fuel pump.

Connect the outlet side of the fuel pump to the inlet side of the fuel bypass filter.

Connect the return line from the bypass filter return port back to the vehicle fuel supply.

Figure 3. Fuel Pump and Filter Detail

Attach the 90 degree elbow and hose barb fittings to the bulkhead connector underneath the vehicle.

Connect a segment of hose between the outlet side of the fuel bypass filter to the hose barb fitting.

Ensure that all hose clamps are properly tightened.

Connect the electrical extension harness to the fuel pump harness, running the other end up through a hole in the
floor of the vehicle, connecting to the console harness.

Figure 4. Vehicle Underside Fuel Line Installation

HOSE INCLUDED
IN TRANSFER KIT

TO FUEL

INJECTION KIT

Содержание 370 SS


















































































Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды

Saphire Scientific 370 SS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 370 SS

Отзывы:

Похожие инструкции для 370 SS

Бренды по названию

Популярные бренды